STM32F103C8T6 ARM STM32 Minimum System Development Board Module for Arduino

Price:
US$13.60
STM32F103C8T6
In stock
+
Add to wish list

STM32F103C8T6 ARM STM32 Minimum System Development Board Module for Arduino

This is a powerful development MCU board by ARM (STM32F103C8T6)

The STM32F103xx medium-density performance line family incorporates the high-performance ARM®Cortex®-M3 32-bit RISC core operating at a 72 MHz frequency, high-speed embedded memories (Flash memory up to 128 Kbytes and SRAM up to 20 Kbytes), and an extensive range of enhanced I/Os and peripherals connected to two APB buses. All devices offer two 12-bit ADCs, three general purpose 16-bit timers plus one PWM timer, as well as standard and advanced communication interfaces: up to two I2Cs and SPIs, three USARTs, an USB and a CAN.

The devices operate from a 2.0 to 3.6 V power supply. They are available in both the –40 to +85 °C temperature range and the –40 to +105 °C extended temperature range. A comprehensive set of power-saving mode allows the design of low-power applications.

These features make the STM32F103xx medium-density performance line microcontroller family suitable for a wide range of applications such as motor drives, application control, medical and handheld equipment, PC and gaming peripherals, GPS platforms, industrial applications, PLCs, inverters, printers, scanners, alarm systems, video intercoms, and HVACs.

SPECIFICATIONS:

 ARM® 32-bit Cortex® -M3 CPU Core

 72 MHz maximum frequency,1.25 DMIPS/MHz (Dhrystone 2.1) performance at 0 wait state memory access

 Single-cycle multiplication and hardware division

 Memories § 64 or 128 Kbytes of Flash memory

 20 Kbytes of SRAM

 Clock, reset and supply management

 2.0 to 3.6 V application supply and I/Os

 POR, PDR, and programmable voltage detector (PVD)

 4-to-16 MHz crystal oscillator

 Internal 8 MHz factory-trimmed RC

 Internal 40 kHz RC

 PLL for CPU clock

 32 kHz oscillator for RTC with calibration

 Low-power

 Sleep, Stop and Standby modes

 VBAT supply for RTC and backup registers

 2 x 12-bit, 1 μs A/D converters (up to 16 channels)

 Conversion range: 0 to 3.6 V

 Dual-sample and hold capability

 Temperature sensor

 DMA

 7-channel DMA controller

 Peripherals supported: timers, ADC, SPIs, I2 Cs and USARTs

 Up to 80 fast I/O ports

 26/37/51/80 I/Os, all mappable on 16 external interrupt vectors and almost all 5 V-tolerant § Debug mode

 Serial wire debug (SWD) & JTAG interfaces

 7 timers

 Three 16-bit timers, each with up to 4 IC/OC/PWM or pulse counter and quadrature (incremental) encoder input

 16-bit, motor control PWM timer with dead-time generation and emergency stop

 2 watchdog timers (Independent and Window)

 SysTick timer 24-bit downcounter

 Up to 9 communication interfaces

 Up to 2 x I2 C interfaces (SMBus/PMBus)

 Up to 3 USARTs (ISO 7816 interface, LIN, IrDA capability, modem control)

 Up to 2 SPIs (18 Mbit/s)

 CAN interface (2.0B Active)

 USB 2.0 full-speed interface

 CRC calculation unit, 96-bit unique ID

 Packages are ECOPACK®

Notice for California Residents: Warning symbolWARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov