GC Waldom

1 2 3 4 5 6 7 8
2 - 11
US$16.93
This is a 2oz bottle of soldering paste. A strong flux for soldering sheet metal parts ,bus wires to steel chassis, tinning and cleaning of soldering iron tips, etc.
In stock
+
Add to wish list

US$24.00

Ready-to-use copper plated printed circuit board has 550 solder tie-points, 94 five-point terminals and two 40-point buss strips on 0.3" centers. Phenolic board has pre-punched holes mounting holes. 2" wide x 6" long x 3/8" thick.

In stock
+
Add to wish list

US$2.74
Material: Delrin Ends: ¼" long Hex, 0.096" dia. shaft; 3/8" long Hex, undercut (0.068" dia.) shaft to reach bottom slugs in coils Total Length: 5" (12.7cm).
In stock
+
Add to wish list

US$13.93

This Deluxe Cable Tie Kit by GC Electronics contains 1000 assorted colored 4 inch cable ties in a handy carrying case.

In stock
+
Add to wish list

US$2.23
Material: Delrin Ends: 0.100" (2.5mm) Hex, 3/8" (9.5mm) long; 1/16" (0.062" - 1.6mm) square, 1/32" (0.1cm) long Total Length: 5 1/16" (12.8cm).
In stock
+
Add to wish list

US$6.19
Shock proof, molded nylon universal fuse pullers. Accommodates all kinds and types of fuses, including house-hold screw-in type and industrial cartridge fuses up to 3/4" or 100 amp type. Non-conductive, non-flammable and virtually unbreakable.
In stock
+
Add to wish list

US$5.59
This is a contact burnishing tool to remove oxide and corrosion.
Delivery within 2-3 weeks
+
Add to wish list

US$4.89
Material: Delrin Ends: ¼" long Hex, 0.096" dia., shaft; 3/8" long Hex, undercut (0.068" dia.) shaft to reach bottom slugs in coils Total Length: 11" (27.9cm).
Delivery within 2-3 weeks
+
Add to wish list

US$5.59
Material: Fibreglass Shaft: 5/32" (4mm) dia., 12" (30.5cm) long Ends: 1/32" thick screwdriver tip (both ends) Total Length: 12" (30.5cm).
In stock
+
Add to wish list

US$4.19
Material: Butyrate Shaft: 7/32" (5.5mm) dia., 15/16" (2.4cm) long Ends: 1/8" (3.2mm) wide steel tip, 3/4" knurled tip Total Length: 5 13/16" (14.8cm).
In stock
+
Add to wish list

US$1.81
This heat sink tool will absorb maximum heat and will fit short leads such as transistors mounted close to PC board.
In stock
+
Add to wish list

US$9.73
This is the perfect tool for assembly of drive belts or assembly and disassembly of springs. On 1 end is the hook design for pulling. The opposite end is designed for pushing.
In stock
+
Add to wish list

US$4.30
Material: Nylon Shaft: ¼" (6.3mm) dia. 4 15/16" (12.5cm) long Ends: 0.85" (2.2mm) wide steel tip; 0.85" (2.2mm) wide steel tip, recessed .040" Total Length: 4 15/16" (12.5cm).
In stock
+
Add to wish list

US$4.12
This plastic hex alignment tool can be used for aligning RF coils as well as adjusting potentiometers in high voltage power supplies. Has a 0.100 inch (2.45mm) hex tip as well as a 0.100 inch (2.45mm) flat screwdriver tip on opposite ends. Tips are undercut to reach the bottom lug of coils without turning the top. Material: Delrin. Length: 11 inch (27.94cm). Adjustment Dimensions: 0.1in. (2.54mm) hex and 0.1 (2.54mm) flat screwdriver.
In stock
+
Add to wish list

US$4.19
Material: Delrin Ends: Flat screwdriver tip (0.027" thick-95" wide), followed by 0.100" Hex, 7/32" long, Undercut shaft to reach bottom slugs in coils. Total Length: 5 3/32" (12.9cm).
In stock
+
Add to wish list
1 2 3 4 5 6 7 8
2 - 11