Our Brands

GC Waldom

1 2 3 4 5 6 7 8
2 - 11
Sort Alphabetically: Z to A
15 Per Page
Soldering Paste
Soldering Paste
US$16.93
This is a 2oz bottle of soldering paste. A strong flux for soldering sheet metal parts ,bus wires to steel chassis, tinning and cleaning of soldering iron tips, etc.
In stock
+ −
Add to wish list
J4-404 PC Board (22-508)
J4-404 PC Board (22-508)
US$24.00

Ready-to-use copper plated printed circuit board has 550 solder tie-points, 94 five-point terminals and two 40-point buss strips on 0.3" centers. Phenolic board has pre-punched holes mounting holes. 2" wide x 6" long x 3/8" thick.

In stock
+ −
Add to wish list
Double Sided Hex tool
Double Sided Hex tool
US$2.74
Material: Delrin Ends: ¼" long Hex, 0.096" dia. shaft; 3/8" long Hex, undercut (0.068" dia.) shaft to reach bottom slugs in coils Total Length: 5" (12.7cm).
In stock
+ −
Add to wish list
CTVP-1000 Cable Tie Kit-4 inch
CTVP-1000 Cable Tie Kit-4 inch
US$13.93

This Deluxe Cable Tie Kit by GC Electronics contains 1000 assorted colored 4 inch cable ties in a handy carrying case.

In stock
+ −
Add to wish list
9440 Square and Hex End Tool
9440 Square and Hex End Tool
US$2.23
Material: Delrin Ends: 0.100" (2.5mm) Hex, 3/8" (9.5mm) long; 1/16" (0.062" - 1.6mm) square, 1/32" (0.1cm) long Total Length: 5 1/16" (12.8cm).
In stock
+ −
Add to wish list
9356 Duo-Tongs
9356 Duo-Tongs
US$6.19
Shock proof, molded nylon universal fuse pullers. Accommodates all kinds and types of fuses, including house-hold screw-in type and industrial cartridge fuses up to 3/4" or 100 amp type. Non-conductive, non-flammable and virtually unbreakable.
In stock
+ −
Add to wish list
9338 GC Tool Contact Burnishing Tools
9338 GC Tool Contact Burnishing Tools
US$5.59
This is a contact burnishing tool to remove oxide and corrosion.
Delivery within 2-3 weeks
+ −
Add to wish list
9293 Double-Ended Long Screwdriver
9293 Double-Ended Long Screwdriver
US$5.59
Material: Fibreglass Shaft: 5/32" (4mm) dia., 12" (30.5cm) long Ends: 1/32" thick screwdriver tip (both ends) Total Length: 12" (30.5cm).
In stock
+ −
Add to wish list
9089 Thin End Steel Tip Tool
9089 Thin End Steel Tip Tool
US$4.19
Material: Butyrate Shaft: 7/32" (5.5mm) dia., 15/16" (2.4cm) long Ends: 1/8" (3.2mm) wide steel tip, 3/4" knurled tip Total Length: 5 13/16" (14.8cm).
In stock
+ −
Add to wish list
902-073 Tool Spring Hook Tool - 8 1/2"
US$9.73
This is the perfect tool for assembly of drive belts or assembly and disassembly of springs. On 1 end is the hook design for pulling. The opposite end is designed for pushing.
In stock
+ −
Add to wish list
8608 Potentiometer Adjustment Tool
8608 Potentiometer Adjustment Tool
US$4.30
Material: Nylon Shaft: ¼" (6.3mm) dia. 4 15/16" (12.5cm) long Ends: 0.85" (2.2mm) wide steel tip; 0.85" (2.2mm) wide steel tip, recessed .040" Total Length: 4 15/16" (12.5cm).
In stock
+ −
Add to wish list
8606-L Hex Aignment Tool
US$4.12
This plastic hex alignment tool can be used for aligning RF coils as well as adjusting potentiometers in high voltage power supplies. Has a 0.100 inch (2.45mm) hex tip as well as a 0.100 inch (2.45mm) flat screwdriver tip on opposite ends. Tips are undercut to reach the bottom lug of coils without turning the top. Material: Delrin. Length: 11 inch (27.94cm). Adjustment Dimensions: 0.1in. (2.54mm) hex and 0.1 (2.54mm) flat screwdriver.
In stock
+ −
Add to wish list
8606 Hex and Special Tip Tool
8606 Hex and Special Tip Tool
US$4.19
Material: Delrin Ends: Flat screwdriver tip (0.027" thick-95" wide), followed by 0.100" Hex, 7/32" long, Undercut shaft to reach bottom slugs in coils. Total Length: 5 3/32" (12.9cm).
In stock
+ −
Add to wish list
8282 Hex-Screwdriver Combination
8282 Hex-Screwdriver Combination
US$2.94
Material: Delrin. Ends: Screwdriver (Plastic) 1/8" Blade; ¼" long Hex, undercut (0.095" dia.) shaft to reach bottom slugs in coils. Total Length: 5 7/16" (13.8cm).
In stock
+ −
Add to wish list
806 Nibbling Tool
806 Nibbling Tool
US$15.39
It will cut any size or shape contour, starting from the edge or from a 3/8" inside hole. This deluxe version is a spring operated nibbler which withdraws the punch from the metal, thereby speeds up the cutting. This tool cuts steel up to 18 gauge (0.046") as well as copper, brass, aluminum and plastics up to 1/16" (0.062").
In stock
+ −
Add to wish list
1 2 3 4 5 6 7 8
2 - 11