FeeTech

1 2 3
CA$44.75
The FeeTech 360 Degrees Digital Servo 7.4V 35kg/cm FT6335M comes with a PA+Aluminum case. The operating voltage range is 6 - 7.4 V and pulse width range 500~2500 usec.
In stock
+
Add to wish list

CA$99.75
The FeeTech 7.4V 65kg 360 Degree Magnetic Encoders Steel Gear Servo comes with a steel gear. It runs on an operating voltage range between 4.8 V - 8.4 V and Idle current (at stopped): 30 mA at 7.4 V. The pulse width range is 500 ~ 2.500 μ sec.
In stock
+
Add to wish list

CA$1.95
The wheels have silicone tires and measure 60 mm (2.36″) in diameter. Two additional mounting holes for 4-40 screws make it possible to use the wheel with our universal mounting hubs for 3mm shafts, 4mm shafts, and 5mm shafts.
In stock
+
Add to wish list

CA$2.95
Suggested Voltage: 3VDC, No Load Speed: 50 ±10 rpm, No Load Current: 150mA, Stall Current: 750mA, Torque: 3Kgf.cm min.
In stock
+
Add to wish list

CA$2.95
Suggested Voltage: 3VDC, No Load Speed: 50 ±10 rpm, No Load Current: 150mA, Stall Current: 750mA, Torque: 3Kgf.cm min.
In stock
+
Add to wish list

CA$19.75
The SCS0009 is a miniature servo that packs a punch. It uses a combination of gears to maximize performance. It has a no-load speed of 143RPM and can output torque of 2.3kg*cm.
In stock
+
Add to wish list

CA$23.75

This is a metal gear digital servo mode motor which can also be used as a continuous mode motor with programming.

In stock
+
Add to wish list

CA$12.23
This version of the FS90 micro servo from FEETECH is specially modified to provide access to the feedback potentiometer through a fourth (green) wire, allowing you to directly measure the position of the output. This extra information enables more complex robotics applications, such as determining when the servo has reached its target, detecting when the output is blocked, or implementing your own higher-level closed-loop position control.
In stock
+
Add to wish list

CA$21.95
This version of the FS5103B standard servo from FEETECH is specially modified to provide access to the feedback potentiometer through a fourth (green) wire, allowing you to directly measure the position of the output. This extra information enables more complex robotics applications, such as determining when the servo has reached its target, detecting when the output is blocked, or implementing your own higher-level closed-loop position control.
In stock
+
Add to wish list

CA$27.42
The FS5323M Metal Gear Digital Servo is a high quality digital servo that is perfect for low cost high torque applications in robotics projects. Comes with a metal anodized servo arm to provide solid thrust transfer. This servo is capable of replacing standard analog servos with the increased speed and torque of a digital servo. This servo can produce high-current draw from your batteries.
Delivery within 2-3 weeks
+
Add to wish list

CA$11.46
The FT90R is a micro-sized digital servo that has been built by FEETECH specifically for continuous rotation. At 6 V, it has a maximum rotation speed of around 170 RPM (no-load) and can produce up to 21 oz-in (1.5 kg-cm) of torque. The servo can be controlled using a direct connection to a single microcontroller I/O line without any additional electronics, which makes it a great miniature actuator for beginner robotics projects; just throw on a pair of wheels (FS90R-W) and your robot is ready to roll!
In stock
+
Add to wish list

CA$73.77
The FT5121M is a standard-size digital servo from FEETECH that can deliver over three times the torque of our standard-size servos with plastic gears thanks to its powerful coreless motor and all-metal gear train (if you need even more torque than this, check out the larger FT5335M giant servo, which can deliver 550 oz-in at 7.4 V, and if you need more speed in a servo with the same dimensions as the FT5121M, consider the FT5313M). The output shaft is supported by two ball bearings for reduced friction.
In stock
+
Add to wish list

CA$69.15
The FT5313M is a standard-size digital servo from FEETECH that can deliver over twice the torque of our standard-size servos with plastic gears thanks to its powerful coreless motor and all-metal gear train (if you need even more torque than this, check out the FT5121M, which has identical dimensions to the FT5313M). The output shaft is supported by two ball bearings for reduced friction. The FT5313M works with standard RC servo pulses, providing a running angle of approximately 120° over a servo pulse range of 900 µs to 2100 µs. Many hobby servos can be operated beyond their standard ranges by using a wider pulse range, but please note that in our tests, we were not able to expand the range of the FT5313M significantly beyond 120° (the servo did not respond to pulses below around 800 µs or above around 2100 µs, providing an approximate expanded range of 135°). This servo has a 10″ (25 cm) cable that is terminated with a standard JR-style connector, which is Futaba-compatible.
In stock
+
Add to wish list

CA$8.85
This is a great general-purpose actuator for tiny mechanisms. The FS0307 is a very small 4.4 g analog servo from FEETECH (formerly known as Fitec) that offers position control over an approximate 120° operating angle for servo pulses between 900 µs and 2100 µs. As with most servos, the pulse range can be expanded to achieve an expanded operating angle, but the limits of this are not specified by FEETECH. (In our tests, we were able to get an expanded range of approximately 180° over a pulse range of 650 µs to 2500 µs, but as this is not part of FEETECH’s official specifications, it is possible different units will behave differently in this regard.)
In stock
+
Add to wish list

CA$8.23
This is a great general-purpose actuator for tiny mechanisms. The FS0403 is a very small 5 g analog servo from FEETECH (formerly known as Fitec) that offers position control over an approximate 120° operating angle for servo pulses between 900 µs and 2100 µs. As with most servos, the pulse range can be expanded to achieve an expanded operating angle, but the limits of this are not specified by FEETECH. (In our tests, we were able to get an expanded range of approximately 180° over a pulse range of 650 µs to 2500 µs, but as this is not part of FEETECH’s official specifications, it is possible different units will behave differently in this regard.) The servo has a 6″ (15 cm) cable that is terminated with a standard JR-style connector, which is Futaba-compatible, and it includes additional servo horns and mounting hardware.
In stock
+
Add to wish list
1 2 3