Test Equipment Kits

ABRA has a vast inventory of Test Equipment kits for teachers, students and hobbyists. If you are a teacher looking for the appropriate kits for your classroom, call our knowledgeable staff for quantity prices and recommendations.
1 2
US$38.49
The main chip is the DIP, easy for electronic enthusiasts to DIY or updates the main chip.Use 9V battery(not included), can also use DC power(DC 6.8-12V).Automatic shutdown, shutdown current is only about 20nA. Rotary switch control, a key measurement for convenient use. Automatically detects NPN and PNP transistors, FET, diodes, dual diode, thyristor, SCR, automatic identification of the transistor pinout. Test NPN and PNP transistor common-emitter current amplification factor, the base-emitter threshold voltage, off the collector-emitter leakage current. Support 2 resistors measurement, show its positive and negative, on-state voltage. Resistance measurement maximum resolution 0.01Ω can be measured up to 50MΩ. Measure FET gate threshold voltage and gate capacitance. Automatically test the pins of a component and show them on the display. Digital LCD display for easy readings, can display measured data and graphics.
In stock
+
Add to wish list

US$54.55
DSO138 was designed as a training oscilloscope kit. Simplicity in structure and easiness in assembly/operation are the main targets of its design. For these purposes, DSO138 applies mostly through-hole parts and the heart of DSO138 is a Cortex-M3 ARM processor (STM32F103C8) from ST. It also uses 2.4-inch TFT LCD (320 X 240 dotmatrix, 262K colors) as its display element that will display nice clear waveforms. Detailed assembly instructions are provided in combination with troubleshooting guide and schematic. This DSO138 kit has all SMD parts pre-soldered. The MCU has been pre-programmed and no re-programming required.
In stock
+
Add to wish list

US$40.90
This is a multimeter kit requiring assembly. Replaces M-1007K device. Supplied: The meter runs off a 9-volt battery (included); two test leads and solder are also included.
In stock
+
Add to wish list

US$19.95

You can build your very own mini waveform generator with this DIY kit. Only supply a constant 9VDC-12VDC and you’ll get this circuit board up and running. With the use of jumpers, you can easily configure the output wave. Choose between a triangle or a sin wave and up to 5 different frequency ranges. Also, for more precise measurements, you can use the available taper potentiometers which also let you control the amplitude of your wave. It also comes with an acrylic case adding an aesthetic element to your kit. Use this opportunity to learn more about the intricacies of assembly and gain experience that will further your understanding of soldering.

In stock
+
Add to wish list

US$22.33
This little device is a frequency counter and crystal frequency tester. It comes with a transparent acrylic enclosure and is simple to assemble. This device is also based on the PIC16F628A allowing users to remove and use the microchip for future uses. It also comes with a 2.1mm connector to USB power from a laptop or desktop. Using the pushbutton you have multiple options available, including the option to save previous measurement!
In stock
+
Add to wish list

US$16.79
This kit will give the user the opportunity to test the frequency of a crystal. The various features of this kit such as adding or subtracting an offset frequency, which can be accessed through its programming mode, will also allow you to use this device in a shortwave receiver or transceiver. This kit is also certainly a perfect choice for those who wish to improve their soldering technique since there are different components to solder.
In stock
+
Add to wish list

US$27.93
Build your own pocket size Inductance, Capacitance and Resistance meter as well as an equivalent series resistance meter jam packed into a single tiny unit. The instruction manual gives a basic outlook of how to toggle into each mode and select the function you desire. This device also offers the option to have a function generator that can go from mHz upto Khz to a max of 2000KHz!
In stock
+
Add to wish list

US$13.93
Build your own digital ammeter and improve your skills in soldering with this D.I.Y kit. This device acts as a current measurement display unit that can measure up to 2 amps. Following our basic and straight forward guide you just have to solder the components into place to get your own ammeter up and running. We also provided a basic black housing for you to put your ammeter into.
In stock
+
Add to wish list

US$23.79
The Decade Resistance Kit allows you to create your very own test instrument, use it to set a specific resistance value and implement it in any design that requires verifying what standard component you would want to use. They come with a nice stylish blue cap to screw onto the 10 position switch knob. This makes it easier to choose the value you want. Choose a value from 10 to 999kΩ by turning the corresponding decimal number to the digits you desire. Please note that the maximum current this unit can handle is approximately 300mA.
In stock
+
Add to wish list

US$12.53
Using the ICL8038 IC, this kit allows you to create a function generator that can create sine waves, square waves and triangle waves. You can adjust the potentiometer for vary the frequency from 200Hz to 2kHz. Play with the other two potentiometers to adjust the duty cycle and adjusting the offset of your signal. This kit is aimed for helping students or beginners in electronics solder their second through-hole board.
In stock
+
Add to wish list

US$51.49
This is an involved PTH soldering kit that allows you to quickly and accurately dial in a specific resistance value between 0 and 999,990 Ω, in 10 Ω increments. The concept is simple, a decade box is a tool that contains resistors of many values that can be accessed via mechanical switches.
Delivery within 2-3 weeks
+
Add to wish list

US$27.25

The board generates a number of safe 'real-world' signals, which we will use to perform measurements. Get familiarized with AC, DC and frequency measurements, sine and square waves, power supply ripple, full and half wave rectifiers, oscillators etc… 

In stock
+
Add to wish list

US$68.25

Build your own oscilloscope and use your PC to display your measurements. This small and easy to build kit has all the features of a full blown oscilloscope, just like the PCSU200 or PCSU1000. Kit comes complete with detailed instructions and test leads. 

In stock
+
Add to wish list

US$48.93
This is a convenient instrument for testing different unshielded wiring schemed telephone cables with RJ-11 and RJ-45 connectors and coax cables (F and BNC connectors).
Cables can be tested before and after they are installed. Do it yourself kit form makes a great educational project. Soft Vinyl Zippered Case (Model C-90) Included.
In stock
+
Add to wish list

US$63.65

This Deluxe Full Function Digital Multimeter Kit is ideal for hobbyists or students. Features: Extra Large 1" ; 3 1/2 Digit Display. AC/DC current to 20A. Capacitance to 200µF. Transistor Tester. Overload Protection. Diode Test. Audio Continuity. Low Battery Indicator. Holster. Tilt Stand. Safety input socket and Test Leads.

In stock
+
Add to wish list
1 2