Our Brands

Adafruit

1 2 3 4 5 6
Newest Items First
128 Per Page
5912-ADA Adafruit SHT41 Trinkey - USB Temperature and Humidity Sensor
US$17.06
5912-ADA  Adafruit SHT41 Trinkey - USB Temperature and Humidity Sensor It's half USB Key, half temperature-humidity sensor, which is a PCB made to...
In stock
+ −
Add to wish list
5896-ADA Adafruit SHT45 Trinkey - USB Temperature and Humidity Sensor
US$27.25
5896-ADA Adafruit SHT45 Trinkey - USB Temperature and Humidity Sensor It's half USB Key, half temperature-humidity sensor, which is a PCB made to...
In stock
+ −
Add to wish list
5723-ADA Adafruit Feather RP2040 with USB Type A Host
US$29.95
The Adafruit Feather RP2040 with USB Host is definitely double-the-fun of our other Feather RP2040 boards, with a USB Type A port on the end for connecting USB devices to.
Delivery within 2-3 weeks
+ −
Add to wish list
4538-ADA NAU7802 Bridge Gauge Sensor Load Cell Module 24-Bit ADC - STEMMA QT/Qwiic
US$9.78
4538-ADA NAU7802 Bridge Gauge Sensor Load Cell Module 24-Bit ADC - STEMMA QT/Qwiic
In stock
+ −
Add to wish list
5880-ADA I2C STEMMA QT / Qwiic Rotary Encoder Breakout with Encoder
US$12.69
5880-ADA I2C STEMMA QT / Qwiic Rotary Encoder Breakout with Encoder
In stock
+ −
Add to wish list
5879-ADA UPDI Friend - USB Serial UPDI Programmer
US$10.87

This module is designed to make programming modern ATtiny chips very easy because it has 3V or 5V power and logic select, power and transmit indicator LEDs, and a quick cable for poking into a breadboard.

Delivery within 2-3 weeks
+ −
Add to wish list
5877-ADA CAN Bus BFF Add-On Module for QT Py
US$14.51
5877-ADA CAN Bus BFF Add-On Module for QT Py
In stock
+ −
Add to wish list
5710-ADA Adafruit Feather RP2040 with DVI Output Port - Works with HDMI
US$25.43
Adafruit Feather RP2040 with DVI Output Port - Works with HDMI
In stock
+ −
Add to wish list
3898-ADA Lithium Ion Polymer Battery Ideal For Feathers - 3.7V 400mAh
US$11.78
The batteries come pre-attached with a genuine 2-pin 25mm long JST-PH connector as shown and include the necessary protection circuitry. Because they have a genuine JST connector, not a knock-off, the cable won't snag or get stuck in a matching JST jack, they click in and out smoothly.
Delivery within 2-3 weeks
+ −
Add to wish list
1196-ADA Slip Ring with Flange - 22mm diameter, 12 wires, max 240V @ 2A
US$31.62
With a slip ring assembly, your electronics can now twist and turn safely. Add wheel encoders, 360 degree sensors, rotating LEDs, rotors and more! We've seen a lot of people DIY slip ring's out of desperation but no longer, simply pick up one of these to solve any rotation needs you have. Inside the plastic tube is a gold plated slip ring for 12 wires. There are 12 color coded wire sets made of 28 AWG and no matter how you twist the assembly, they will remain in continuity.
Delivery within 2-3 weeks
+ −
Add to wish list
956-ADA Miniature 8x8 Blue LED Matrix, Common Cathode
US$9.05
Miniature 8x8 Blue LED Matrix, Common Cathode   You will squeal with delight when you hold this adorable miniature LED matrix. 0.8" square, its got...
In stock
+ −
Add to wish list
4907-ADA USB C SMT / THM Jack Connector - Power Only - Pack of 10
US$4.32
If you're a DIY enthusiast who'd like to update your power only project's connection to the latest USB standard, here is a 10-pack of USB C power only jack connectors! They're sturdy metal with 4 through-hole mounting tabs. It's really hard to rip these off a PCB. In an SMT line, you can just paste over the through-hole slots, and the pads will solder in place.
In stock
+ −
Add to wish list
4909-ADA 40-pin FPC to Right Angle 2x20 IDC Female Socket Header
US$5.41
This is a 40-pin FPC to Right Angle 2x20 IDC Female Socket Header Adapter. Use this adapter, which will act as an extender for all 40 pins to give you a streeeeetch. Simply plug the socket side into the Raspberry Pi. Then, keeping an eye where Pin 1 is, insert your FPC ribbon cable into the 40-pin flex connector.
Delivery within 2-3 weeks
+ −
Add to wish list
4905-ADA 40-pin FPC to Straight 2x20 IDC Female Socket Header
US$5.41
This is a 40-pin FPC to Straight 2x20 IDC Female Socket Header Adapter. Use this adapter, which will act as an extender for all 40 pins to give you a streeeeetch. Simply plug the socket side into the Raspberry Pi. Then, keeping an eye where Pin 1 is, insert your FPC ribbon cable into the 40-pin flex connector.
In stock
+ −
Add to wish list
3244-ADA Mini 3-Layer Round Robot Chassis Kit - 2WD with DC Motors
US$38.90
This kit gives you everything you need to build the shell of a 2-wheel-drive Mobile Platform Robot! You get the metal plates that make up the chassis, two DC drive motors with matching wheels, and a caster ball for balance. You'll fill in the rest with a power supply, microcontroller board, and motor controller. The differential drive (two separately driven wheels) allows for a near zero turning radius while the high-strength aluminum alloy body plus high-quality high-speed motors make it suitable for flat indoor surfaces.
Delivery within 2-3 weeks
+ −
Add to wish list
5753-ADA Adafruit PC Joystick to seesaw I2C Adapter - STEMMA QT / Qwiic
US$9.05
This board has a 15 pin D-Sub socket port, that you can plug any classic PC joystick into. Onboard is a ATtiny816 helper chip that acts as a I2C peripheral using our 'seesaw' library. Two STEMMA QT ports mean you can plug this board in using a 4-pin JST SH cable to any microcontroller or microcomputer with I2C support and read the joystick X & Y plus the two buttons, even if your main chip doesn't have analog inputs. There's even a 5V power generator on-board since joysticks are expecting that voltage.
In stock
+ −
Add to wish list
5786-ADA Adafruit Metro RP2040
US$22.70
The RP2040 is a powerful chip, which has the clock speed of our M4 (SAMD51), and two cores that are equivalent to our M0 (SAMD21). Since it is an M0 chip, it does not have a floating point unit or DSP hardware support - so if you're doing something with heavy floating-point math, it will be done in software and thus not as fast as an M4. For many other computational tasks, you'll get close-to-M4 speeds!
In stock
+ −
Add to wish list
4470-ADA Adafruit MCP4728 Quad DAC with EEPROM - STEMMA QT / Qwiic
US$11.78
The MCP4728 lets you chose between two sources for your reference voltage: the input voltage that you use to power it on the VCC pin, or an internal 2.048V reference voltage. If you use the internal reference voltage (Vref in DAC speak) you can choose between 1X or 2X gain for the output, allowing your voltages to range from 0V to 2.048 or 0V to 4.096V as your application requires.
In stock
+ −
Add to wish list
4900-ADA Adafruit QT Py RP2040
US$15.42
The star of the QT Py is our favorite connector - the STEMMA QT, a chainable I2C port that can be used with any of our STEMMA QT sensors and accessories. Having this connector means you don't need to do any soldering to get started. What can you pop into the QT port? How about OLEDs! Inertial Measurment Units! Sensors a-plenty. All plug-and-play thanks to the innovative chainable design: SparkFun Qwiic-compatible STEMMA QT connectors for the I2C bus so you don't even need to solder. Just plug in a compatible cable and attach it to your MCU of choice, and you’re ready to load up some software and measure some light.
Delivery within 2-3 weeks
+ −
Add to wish list
BB-RCA-M-SP RCA Male Jack to Terminal Block Spring-Loaded
US$1.77
RCA Male Jack to spring-load Terminal Block for video and audio applications.
Delivery within 2-3 weeks
+ −
Add to wish list
4055-ADA Snap-In Panel Mount Cable - USB A Extension Cable
US$8.87
This panel mount cable will allow you to enclose a device that has a USB A port. Perfect for placing your project in a secure box. Both ends have standard USB A, an extension cord if you will.
In stock
+ −
Add to wish list
4259-ADA USB C Jack to USB A Jack Round Panel Mount Adapter
US$9.96
If you need to add a panel-mount connection for USB C, but don't have the time or tools to cut a custom oval or square hole, this Round Panel Mount Plug is the easiest and fastest way to panel-ify your project.
In stock
+ −
Add to wish list
SENS-AM2302 Temperature-Humidity Capacitance DHT22 Sensor
US$12.69
SENS-AM2302 Temperature-Humidity Capacitance DHT22 Sensor .
It uses a capacitive humidity sensor and a thermistor to measure the surrounding air, and sends out a digital signal on the data pin.
In stock
+ −
Add to wish list
SEN0539-EN Gravity: Offline Language Learning Voice Recognition Sensor for Arduino / Raspberry Pi / Python / ESP32 - I2C & UART
US$27.07
This Gravity: Offline Voice Recognition Sensor is built around an offline voice recognition chip, which can be directly used without an internet connection. It comes with 121 built-in fixed command words and supports the addition of 17 custom command words. Any sound could be trained as a command, such as whistling, snapping, or even cat meows, which brings great flexibility to interactive audio projects.
In stock
+ −
Add to wish list
ARD-MAX7219-GN, Small Green 1.2" 8x8 LED Matrix with MAX7219 Module
US$5.41
Small Green 1.2" 8x8 LED Matrix with MAX7219 Module The MAX7219 is compact, serial input/output common-cathode display drivers that interface...
In stock
+ −
Add to wish list
3857-ADA Adafruit Feather M4 Express - Featuring ATSAMD51 - ATSAMD51 Cortex M4
US$36.35
This feather is powered by our new favorite chip, the ATSAMD51J19 - with its 120MHz Cortex M4 with floating point support and 512KB Flash and 192KB RAM. Your code will zig and zag and zoom, and with a bunch of extra peripherals for support, this will for sure be your favorite new chipset.
In stock
+ −
Add to wish list
5637-ADA Adafruit QT 5V to 3V Level Shifter Breakout - STEMMA QT / Qwiic
US$5.14
The STEMMA QT connectors on either side are compatible with the I2C connectors. This allows you to make solderless connections between your development board and the QT Shifter or to chain it with a wide range of other sensors and accessories using a compatible cable.
Delivery within 2-3 weeks
+ −
Add to wish list
4210-ADA STEMMA QT / Qwiic JST SH 4-pin Cable - 100mm Long
US$2.23
This 4-wire cable is a little over 100mm / 4" long and fitted with JST-SH female 4-pin connectors on both ends. Compared with the chunkier JST-PH these are 1mm pitch instead of 2mm, but still have a nice latching feel, while being easy to insert and remove.
In stock
+ −
Add to wish list
5046-ADA Adafruit BME688 - Temperature, Humidity, Pressure and Gas Sensor - STEMMA QT
US$31.62
The long-awaited BME688 from Bosch gives you all the environmental sensing you want in one small package. This little sensor contains temperature, humidity, barometric pressure, and VOC gas sensing capabilities. All over SPI or I2C at a great price! The BME688 is a 'drop in' replacement for the BME680 - it adds a method of programming the gas-sensor heater for controlled odor-analysis but is otherwise the same hardware.
In stock
+ −
Add to wish list
5300-ADA Adafruit ESP32-S2 TFT Feather - 4MB Flash, 2MB PSRAM, STEMMA QT
US$38.90
This feather comes with native USB and 4 MB flash + 2 MB of PSRAM, so it is perfect for use with CircuitPython or Arduino with low-cost WiFi. Native USB means it can act like a keyboard or a disk drive. WiFi means its awesome for IoT projects. And Feather means it works with the large community of Feather Wings for expandability.
Delivery within 2-3 weeks
+ −
Add to wish list
5591-ADA Adafruit LTR-329 Light Sensor - STEMMA QT / Qwiic
US$7.23
The Adafruit LTR-329 Light Sensor a simple and popular low-cost I2C digital light sensor that is easy to integrate into your project for reliable and wide-ranging light measurements.
In stock
+ −
Add to wish list
5610-ADA Adafruit LTR-303 Light Sensor - STEMMA QT / Qwiic
US$7.23
The Adafruit LTR-303 Light Sensor a simple and popular low-cost I2C digital light sensor that is easy to integrate into your project for reliable and wide-ranging light measurements.
In stock
+ −
Add to wish list
3213-ADA Assembled Feather HUZZAH w/ ESP8266 WiFi With Stacking Headers
US$31.62
Feather is the new development board from Adafruit, and like its namesake, it is thin, light, and lets you fly! We designed Feather to be a new standard for portable microcontroller cores. This is the Adafruit Feather HUZZAH ESP8266 - our take on an 'all-in-one' ESP8266 WiFi development board with built-in USB and battery charging. It's an ESP8266 WiFi module with all the extras you need, ready to rock!
Delivery within 2-3 weeks
+ −
Add to wish list
4991-ADA Adafruit I2C Stemma QT Rotary Encoder Breakout with NeoPixel - STEMMA QT / Qwiic
US$9.05
This Stemma QT breakout makes all that frustration go away - solder in any 'standard' PEC11-pinout rotary encoder with or without a push-switch. The onboard microcontroller is programmed with our seesaw firmware and will track all pulses and pins for you and then save the incremental value for querying at any time over I2C. Plug it in with a Stemma QT cable for instant rotary goodness, with any kind of microcontroller from an Arduino UNO up to a Raspberry Pi.
In stock
+ −
Add to wish list
5545-ADA, Adafruit PCF8574 I2C GPIO Expander Breakout - STEMMA QT / Qwiic
US$7.23
The ADAFRUIT 5545 is a GPIO Expander Breakout - an affordable 8-channel I2C expander.
In stock
+ −
Add to wish list
5543-ADA, Adafruit LSM6DS3TR-C + LIS3MDL - Precision 9 DoF IMU - STEMMA QT / Qwiic
US$27.25
The 5543-ADA is a high-quality sensor that integrates two powerful chips to create a strong and reliable motion, direction and orientation sensor!
Delivery within 2-3 weeks
+ −
Add to wish list
4503-ADA, Adafruit LSM6DS3TR-C 6-DoF Accel + Gyro IMU - STEMMA QT / Qwiic
US$16.33
Le 4503-ADA est une carte de dérivation pour capteur d'accéléromètre et de gyroscope.
In stock
+ −
Add to wish list
2305-ADA, Adafruit DRV2605L Haptic Motor Controller - STEMMA QT / Qwiic
US$12.69
The 2305-ADA is a vibration motor controller about the size of a quarter.
Delivery within 2-3 weeks
+ −
Add to wish list
5383-ADA, Single Li-Ion and LiPoly Battery Power Meter
US$4.50
The 5383-ADA is a small Li-po and Li-ion battery meter. It has a very simplistic design and is easy to install on any battery.
In stock
+ −
Add to wish list
5384-ADA, STEMMA QT / Qwiic JST SH 4-Pin Cable - 300mm long
US$2.50
The 5384-ADA is a 300mm 4 wire connector. It is fitted with JST-SH and has a solid latch that makes it easier to insert.
 
In stock
+ −
Add to wish list
5445-ADA, WiFi Antenna with w.FL / MHF3 / IPEX3 Connector
US$4.05
The 5445-ADA is a small antenna that supports 2.4GHz WiFi or BLE.
In stock
+ −
Add to wish list
5462-ADA, EYESPI Cable - 18-pin 50mm long Flex PCB (FPC) A-B Type
US$1.68
The 5462-ADA is a 50mm 18 pin connector.
In stock
+ −
Add to wish list
5385-ADA, STEMMA QT / Qwiic JST SH 4-Pin Cable - 400mm long
US$2.68
The 5385-ADA is a 400mm 4 wire connector. It is fitted with JST-SH and has a solid latch that makes it easier to insert.
In stock
+ −
Add to wish list
5303-ADA, Adafruit ESP32-S2 Feather with BME280 Sensor - STEMMA QT - 4MB Flash + 2 MB PSRAM
US$36.17
The 5303-ADA is an ESP32-S2 module with 4MB of flash and 2MB of PSRAM. It also has a built-in BME280 Sensor, which detects temperature, humidity and pressure. Hurry! Before this product flies off the shelves!
Delivery within 2-3 weeks
+ −
Add to wish list
3405-ADA Adafruit HUZZAH32 – ESP32 Feather Board
US$29.80
The HUZZAH32 is an ESP32-based Feather, made with the official WROOM32 module. It has built in USB-to-Serial converter, automatic bootloader reset, Lithium Ion/Polymer charger, and just about all of the GPIOs brought out so you can use it with any of our Feather Wings.
In stock
+ −
Add to wish list
5000-ADA, Adafruit ESP32-S2 Feather - 2 MB PSRAM and STEMMA QT / Qwiic
US$27.25
The 5000-ADA is a highly-integrated, low-power, 2.4 GHz Wi-Fi System-on-Chip (SoC) solution that now has built-in native USB as well as some other interesting new technologies like Time of Flight distance measurements. With its state-of-the-art power and RF performance, this SoC is an ideal choice for a wide variety of application scenarios relating to the Internet of Things (IoT), wearable electronics, and smart homes.
Delivery within 2-3 weeks
+ −
Add to wish list
BB-RCA-F-SP RCA Female Jack to Terminal Block Spring-Loaded
US$1.77
RCA Female Jack to spring-load Terminal Block for video and audio applications.
In stock
+ −
Add to wish list
4516-ADA Adafruit Feather nRF52840 Sense
US$57.83
This Feather microcontroller comes with Bluetooth Low Energy and native USB support featuring the nRF52840! This Feather is an 'all-in-one' Arduino-compatible + Bluetooth Low Energy with built in USB plus battery charging. With native USB it works great with CircuitPython, too.
Delivery within 2-3 weeks
+ −
Add to wish list
4062-ADA Adafruit Feather nRF52840 Express
US$36.35
This chip has twice the flash, and four times the SRAM of its earlier sibling, the nRF52832 - 1 MB of FLASH and 256KB of SRAM. Compared to the nRF51, this board has 4-8 times more of everything. For this chip, we've added Arduino IDE support - you can program the nRF52840 chip directly to take full advantage of the Cortex-M4 processor, and then calling into the Nordic SoftDevice radio stack when you need to communicate over BLE. Since the underlying API and peripherals are the same for the '832 and '840, you can supercharge your older nRF52832 projects with the same exact code, with a single recompile!
Delivery within 2-3 weeks
+ −
Add to wish list
4500-ADA Adafruit CLUE - nRF52840 Express with Bluetooth LE
US$59.10
Get a CLUE here at Adafruit by picking up this sensor-packed development board. We wanted to build some projects that have a small screen and a lot of sensors. To make it compatible with existing projects, we made it the same shape and size as the BBC micro:bit and with the same edge-connector on the bottom with 5 big pads so it will fit into your existing robot kit or 'bit add-on.
Delivery within 2-3 weeks
+ −
Add to wish list
40 Pin GPIO Extension Cable for any 2x20 Pin Raspberry Pi - 150mm / 6" long
US$4.54
Unlike the 'classic' Raspberry Pi computers, you can't really stick a HAT, bonnet, pHAT or other accessory/add-on on top...what to do? Give up!? NO! Use this cable, which will act as an extender for all 40 pins to give you a stretch of about 150mm / 6 inches. Simply plug the socket side into the Raspberry Pi with the white mark next to the Pin 1 label. Then on the other side, plug the hat down onto the plug side.
In stock
+ −
Add to wish list
2x20 Socket Riser Header for Raspberry Pi HATs and Bonnets
US$3.17
Give yourself a lift with this 2x20 female socket header that has slightly longer than usual pins. You can plug this into your Raspberry Pi GPIO port and then plug a HAT or Bonnet or Phat on top. Especially useful for Bonnets that have slim headers on the bottom, but you want them to clear some of the components on the Pi, or fit into a case nicer.
Delivery within 2-3 weeks
+ −
Add to wish list
MPM3610 5V Buck Converter Breakout - 21V In 5V Out at 1.2A
US$9.05
This little buck converter based on the MPM3610 is a marvel, taking up to 21V input and providing a 5V output with up to 1.2A current. It's great for supplying power to popular 5V voltage circuits from a range of battery or power options.  This chip provides up to 1.2 Amp load current across the entire input voltage range of 6V to 21V. The high voltage range is what sets this buck converter apart from most!
In stock
+ −
Add to wish list
JST-PH 2-pin Jumper Cable - 100mm long
US$1.80
Both ends have a JST PH 2mm pitch 2-pin plug. Between the two, 100mm of color coded wire - red for power, black for ground. No more soldering two pig-tails together!
In stock
+ −
Add to wish list
Adafruit LIS331 Triple-Axis Wide-Range ±24g Accelerometer - STEMMA QT / Qwiic
US$17.17
The LIS331HH is capable of measuring ±6g/±12g/±24g on each of its three axes! Compare that with most other accelerometers such as the LIS3DH, which can only handle ±2g/±4g/±8g/16g.
In stock
+ −
Add to wish list
Adafruit LPS22 Pressure Sensor - STEMMA QT / Qwiic - LPS22HB
US$10.45
This absolute pressure sensor, ST LPS22HB (a.k.a LPS22) can quickly and easily measure this air pressure, useful when you want to know about the weather (are we in a low-pressure or high-pressure system?) or to determine altitude, as the air thins out the higher we get above sea level.
In stock
+ −
Add to wish list
Adafruit 9-DOF LSM9DS1 Breakout Board - STEMMA QT / Qwiic
US$57.95
Add motion, direction and orientation sensing to your project with this all-in-one 9-DOF sensor that is STEMMA QT ready for easy plug-n-play usage. Inside the chip are three sensors, one is a classic 3-axis accelerometer, which can tell you which direction is down towards the Earth (by measuring gravity) or how fast the board is accelerating in 3D space.
In stock
+ −
Add to wish list
Adafruit Sensirion SHTC3 Temperature & Humidity Sensor - STEMMA QT / Qwiic
US$10.45
Sensirion Temperature/Humidity sensors are some of the finest & highest-accuracy devices you can get. And finally, we have some that have a true I2C interface for easy reading. The SHTC3 sensor has an excellent ±2% relative humidity and ±0.2 °C accuracy for most uses. Unlike some earlier SHT sensors, this sensor has a true I2C interface on address 0x70.
In stock
+ −
Add to wish list
Mini Pan-Tilt Kit - Assembled with Micro Servos
US$27.25
This fully-assembled pan-tilt kit is the perfect way to give your project full range motion with two micro servos. The pan-tilt can rotate roughly 180° from side-to-side and can tilt up&downwards around 150°. It also comes fully assembled with two Micro Servos (SG-90 or SG-92 type) included and a 38mm x 36mm space to mount a camera or sensor or whatever you like.
Delivery within 2-3 weeks
+ −
Add to wish list
3144-ADA Large Dual Row Wire Housing Pack for DIY Jumper Cables
US$7.49

Compatible with both male and female wires, these fully customizable wire housings bring DIY to a new level, giving you near limitless options when using jumper wires in your project. This is a pack of small, dual row housings. This pack includes: 5 x 2x2 housing, 5 x 2x3 housing, 5 x 2x4 housing, 5 x 2x5 housing, 5 x 2x6 housing. 

In stock
+ −
Add to wish list
USB Cable with Switch
US$5.75
Comes with a USB A socket on one end and a USB A plug on the other. In between is an in-line switch that is rated for 2 Amps. The data lines are not connected through - this is a ground/5V power switch only! The switch is on the positive 5V line.
In stock
+ −
Add to wish list
STEMMA Wired Potentiometer Breakout Board - 10K ohm Linear
US$5.99
For the easiest way possible to measure twists, turn to this STEMMA potentiometer breakout (ha!). This plug-n-play pot comes with a JST-PH 2mm connector and a matching  JST PH 3-Pin to Male Header Cables - 200mm, so wiring up is a cinch.
In stock
+ −
Add to wish list
Adafruit DPS310 Precision Barometric Pressure / Altitude Sensor - STEMMA QT / Qwiic
US$10.99
The DPS310 sensor from Infineon a high precision barometric sensor, perfect for measuring altitude changes with a up to ±0.002 hPa (or ±0.02 m) precision high precision mode and ± 1 hPa absolute accuracy. That means you can know your absolute altitude with 1 meter accuracy when you set the sea-level pressure, and measure changes in altitude with up to 2 cm precision.
In stock
+ −
Add to wish list
Adafruit ISM330DHCX - 6 DoF IMU - Accelerometer and Gyroscope - STEMMA QT / Qwiic
US$22.99
This IMU sensor has 6 degrees of freedom - 3 degrees each of linear acceleration and angular velocity at varying rates within a respectable range. For the accelerometer: ±2/±4/±8/±16 g at 1.6 Hz to 6.7KHz update rate. For the gyroscope: ±125/±250/±500/±1000/±2000/±4000 dps at 12.5 Hz to 6.7 KHz.
In stock
+ −
Add to wish list
USB Type C Socket - SMT Inline Breakout Board
US$5.49
This USB Type C breakout is kinda interesting, it looks similar to our right angle USB C socket breakout, but it's an 'inline' style with pads for soldering to the connections. We think it could be handy for making custom cable harnesses!
In stock
+ −
Add to wish list
Adafruit Triple-axis Magnetometer - LIS3MDL - STEMMA QT / Qwiic
US$15.42
Sense the magnetic fields that surround us with this handy triple-axis magnetometer (compass) module. Magnetometers can sense where the strongest magnetic force is coming from, generally used to detect magnetic north, but can also be used for measuring magnetic fields. This sensor tends to be paired with a 6-DoF (degree of freedom) accelerometer/gyroscope to create a 9-DoF inertial measurement unit that can detect its orientation in real-space thanks to Earth's stable magnetic field.
In stock
+ −
Add to wish list
Adafruit LSM6DSOX 6 DoF Accelerometer and Gyroscope - STEMMA QT / Qwiic
US$18.45
This IMU sensor has 6 degrees of freedom - 3 degrees each of linear acceleration and angular velocity at varying rates within a respectable range. For the accelerometer: ±2/±4/±8/±16 g at 1.6 Hz to 6.7KHz update rate. For the gyroscope: ±125/±250/±500/±1000/±2000 dps at 12.5 Hz to 6.7 KHz.
Delivery within 2-3 weeks
+ −
Add to wish list
Adafruit MCP2221A Breakout - General Purpose USB to GPIO ADC I2C - Stemma QT / Qwiic
US$9.99
What can the MCP2221 chip do?  This chip from Microchip is similar to a USB to serial converter chips but adds a GPIO and I2C interface as well. The analog/digital GPIO pins can act as 10-bit analog inputs (ADC) and there's even a 5-bit DAC output. The I2C interface is great for talking to OLEDs, sensors, PWM drivers, its the most popular interface for small devices.
Delivery within 2-3 weeks
+ −
Add to wish list
Adafruit Mini PiTFT 1.3" - 240x240 TFT Add-on for Raspberry Pi
US$22.95
This product is your little TFT pal, ready to snap onto any and all Raspberry Pi computers, to give you a little display. The Mini PiTFT comes with a full color 240x240 pixel IPS display with great visibility at all angles. The TFT uses only the SPI port so its very fast, and we leave plenty of pins remaining available for buttons, LEDs, sensors, etc. It's also nice and compact so it will fit into any case.
In stock
+ −
Add to wish list
Adafruit e-Ink Feather Friend with 32KB SRAM
US$13.79
We've liked these displays for a long time, and we've got Arduino/CircuitPython drivers for all of our Feathers, so wouldn't an e-paper Feather Friend make a ton of sense? Luckily for us, just about every small-medium size EInk display made these days has a standard 24-pin connection. This Friend will add all the power supply support circuitry and level shifting so you can attach your favorite display (up to tri-color 4.2") and wire it up to your favorite development board.
In stock
+ −
Add to wish list
Mono Enclosed Speaker - 3W 4 Ohm
US$5.99
Listen up! This 2.8" x 1.2" speaker is a great addition to any audio project where you need 4 ohm impedance and 3W or less of power. We particularly like this speaker as it is small and enclosed for good audio volume and quality. It has a handy JST 2PH input cable to add audio to your displays and other projects (this connector is part of the JST-PH series which is ~2.0mm spacing).
In stock
+ −
Add to wish list
Mono Enclosed Speaker with Plain Wires - 3W 4 Ohm
US$5.99
This single  2.8" x 1.2" speaker is the perfect addition to any audio project where you need 4 ohm impedance and 3W or less of power. We particularly like these speakers as they are small and enclosed for good audio volume and quality. This speaker does not come with a connector on the end, it's just plain bare wires!
In stock
+ −
Add to wish list
CAP1188 - 8-Key Capacitive Touch Sensor Breakout - I2C or SPI
US$13.92
Add lots of touch sensors to your next microcontroller project with this easy-to-use 8-channel capacitive touch sensor breakout board, starring the CAP1188. This chip can handle up to 8 individual touch pads, and has a very nice feature that makes it stand out for us: it will light up the 8 onboard LEDs when the matching touch sensor fires to help you debug your sensor setup.
Delivery within 2-3 weeks
+ −
Add to wish list
Adafruit LPS33HW Water Resistant Pressure Sensor - STEMMA QT
US$17.52
Sometimes you need to sense pressure in a damp or caustic environment. And sometimes you need to know the relative changes in pressure as well as the absolute pressure. For the times you need to do both (or either), the LPS33HW is the pressure sensor for you. Combining protection from water intrusion with support for high precision relative and absolute measurements, this sensor will do what you need.
In stock
+ −
Add to wish list
Assembled Adafruit Feather M0 WiFi - ATSAMD21 + ATWINC1500
US$56.95
Feather is the new development board from Adafruit, and like its namesake, it is thin, light, and lets you fly! We designed Feather to be a new standard for portable microcontroller cores. This is the Assembled Adafruit Feather M0 WiFi w/ATWINC1500 - our take on an 'all-in-one' Arduino-compatible + high speed, reliable WiFi with built in USB and battery charging. Its an Adafruit Feather M0 with a WiFi module.
In stock
+ −
Add to wish list
Monochrome 0.91" 128x32 I2C OLED Display - STEMMA QT / Qwiic Compatible
US$19.95
These displays are small, only about 1" diagonal, but very readable due to the high contrast of an OLED display. This display is made of 128x32 individual white OLED pixels, each one is turned on or off by the controller chip. Because the display makes its own light, no backlight is required. This reduces the power required to run the OLED and is why the display has such high contrast; we really like this miniature display for its crispness!
Delivery within 2-3 weeks
+ −
Add to wish list
JST PH 3-pin Horizontal Connector (10-pack) - STEMMA
US$5.49
Designing boards with plug-n-play connectivity is a snap, with STEMMA connectors. Here's a pack of 10 of our favorite 2mm pitch connector - the JST PH 3 pin. These are the horizontal style.
In stock
+ −
Add to wish list
JST PH 3-pin Vertical Connector (10-pack) - STEMMA
US$5.49
Designing boards with plug-n-play connectivity is a snap, with STEMMA connectors. Here's a pack of 10 of our favorite 2mm pitch connector - the JST PH 3 pin. These are the vertical style.
In stock
+ −
Add to wish list
JST PH 4-pin Horizontal Connector (10-pack) - STEMMA
US$5.49
Designing boards with plug-n-play connectivity is a snap, with STEMMA connectors. Here's a pack of 10 of our favorite 2mm pitch connector - the JST PH 4 pin. These are the horizontal style.
In stock
+ −
Add to wish list
JST PH 4-pin Vertical Connector (10-pack) - STEMMA
US$5.49
Designing boards with plug-n-play connectivity is a snap, with STEMMA connectors. Here's a pack of 10 of our favorite 2mm pitch connector - the JST PH 4 pin. These are the vertical style.
In stock
+ −
Add to wish list
STEMMA QT / Qwiic JST SH 4-Pin Cable - 200mm Long
US$1.79
This 4-wire cable is a little over 200mm / 7.8" long and fitted with JST-SH female 4-pin connectors on both ends. Compared with the chunkier JST-PH these are 1mm pitch instead of 2mm, but still have a nice latching feel, while being easy to insert and remove.
In stock
+ −
Add to wish list
STEMMA QT / Qwiic JST SH 4-Pin Cable - 50mm Long
US$1.79
This 4-wire cable is 50mm / 1.9" long and fitted with JST SH female 4-pin connectors on both ends. Compared with the chunkier JST PH these are 1mm pitch instead of 2mm, but still have a nice latching feel, while being easy to insert and remove.
In stock
+ −
Add to wish list
JST SH 4-pin Cable with Alligator Clips - STEMMA QT / Qwiic
US$4.99
This cable will make it super easy to use our plug-and-play STEMMA QT boards with boards like Circuit Playground. On one end you get a Qwiic / STEMMA QT connector (technically known as a JST SH 4-pin plug) into 4 individual wires with grippy alligator clips. We're carrying these to match up with our boards or breakouts with 'STEMMA QT' connectors on them.
In stock
+ −
Add to wish list
JST PH 4-Pin to Female Socket Cable - I2C STEMMA Cable - 200mm
US$2.49
This cable will let you turn a JST PH 4-pin cable port into 4 individual wires with high-quality 0.1" female sockets on the end. We're carrying these to match up with any of our boards with 'STEMMA' connectors on them.
In stock
+ −
Add to wish list
3-pin JST SM Plug + Receptacle Cable Set
US$2.49
These 3-wire cables are 163mm (6.4") long and come as a set. One cable has a JST SM type connector plug on the end. The other cable has a matching JST SM type receptacle connector. They are good for whenever you have 3 wires you want to be able to plug and unplug.
In stock
+ −
Add to wish list
STEMMA QT / Qwiic JST SH 4-pin to Premium Male Headers Cable - 150mm Long
US$1.89
This 4-wire cable is a little over 150mm / 6" long and fitted with JST-SH female 4-pin connectors on one end and premium Dupont male headers on the other. Compared with the chunkier JST-PH these are 1mm pitch instead of 2mm, but still have a nice latching feel, while being easy to insert and remove.
In stock
+ −
Add to wish list
Adafruit Mini GPS PA1010D - UART and I2C - STEMMA QT
US$30.44
This miniature GPS breakout is only 1" x 1" (~ 25mm x 25mm) but houses a complete GPS/GNSS solution with both I2C and UART interfaces. There's even an antenna on top so it's plug and play!
Delivery within 2-3 weeks
+ −
Add to wish list
Adafruit LSM303AGR Accelerometer Magnetometer - STEMMA QT Qwiic
US$13.79
Inside are two sensors, one is a classic 3-axis accelerometer, which can tell you which direction is down towards the Earth (by measuring gravity). The other is a magnetometer that can sense where the strongest magnetic force is coming from, generally used to detect magnetic north. By combining this data you can then orient your project!
In stock
+ −
Add to wish list
Adafruit MPU-6050 6-DoF Accel and Gyro Sensor - STEMMA QT Qwiic
US$20.30
Inside are two sensors, one is a classic 3-axis accelerometer, which can tell you which direction is down towards the Earth (by measuring gravity). The other is a gyroscoe that can sense how fast the board is being twisted around. By combining this data you can tell how your project is moving through space
In stock
+ −
Add to wish list
JST PH 4-Pin Socket to Color Coded Cable - 200mm
US$1.49
This cable will let you turn a JST PH 3-pin cable socket into 4 individual tinned wires. These are great to match up with our JST 4-PH cables, for extending and connecting sensors or LEDs, and the wires are even color coded!
In stock
+ −
Add to wish list
FTDI Serial TTL-232 USB Type C Cable - 5V Power and Logic
US$30.95
This is a USB C to TTL serial cable with an FTDI FT232R usb/serial chip embedded in the head. It has a 6-pin socket at the end with 5V power and ground, as well as RX, TX, RTS and CTS at 3V logic levels. Useful whenever you want to communicate with a TTL serial device and the pinout will match up exactly to any 'FTDI' 6-pin header.
In stock
+ −
Add to wish list
Adafruit 1.14" 240x135 Color TFT Display + MicroSD Card Breakout - ST7789
US$21.61
This lovely little display breakout is the best way to add a small, colorful and very bright display to any project. Since the display uses 4-wire SPI to communicate and has its own pixel-addressable frame buffer, it can be used with every kind of microcontroller. Even a very small one with low memory and few pins available! The 1.14" display has 240x135 16-bit full color pixels and is an IPS display, so the color looks great up to 80 degrees off axis in any direction.
In stock
+ −
Add to wish list
5-pin JST SM Plug + Receptacle Cable Set
US$2.39
These 5-wire cables are 168mm (6.6") long and come as a set. One cable has a JST SM type connector plug on the end. The other cable has a matching JST SM type receptacle connector. They are good for whenever you have 5 wires you want to be able to plug and unplug.
In stock
+ −
Add to wish list
6-pin JST SM Plug + Receptacle Cable Set
US$2.39
These 6-wire cables are 162mm (6.4") long and come as a set. One cable has a JST SM type connector plug on the end. The other cable has a matching JST SM type receptacle connector. They are good for whenever you have 6 wires you want to be able to plug and unplug.
In stock
+ −
Add to wish list
JST PH 2-Pin Cable – Male Header 200mm
US$1.29
Plugs in nicely with our Li-Poly batteries, it even has the right color coding!
In stock
+ −
Add to wish list
JST PH 3-Pin Socket to Color Coded Cable - 200mm
US$1.49
This cable will let you turn a JST PH 3-pin cable socket into 3 individual tinned wires. These are great to match up with our JST 3-PH cables, for extending and connecting sensors or LEDs, and the wires are even color coded!
In stock
+ −
Add to wish list
JST PH 3-pin Plug to Color Coded Alligator Clips Cable
US$2.99
This cable has a JST PH 3-pin on one side and alligator clips on the other, so it could be used to connect to wires or pads like that on the Circuit Playground or micro:bit.
In stock
+ −
Add to wish list
FTDI Serial TTL-232 USB Type C Cable - 3V Power and Logic
US$30.73
This is a USB C to TTL serial cable with an FTDI FT232R usb/serial chip embedded in the head. It has a 6-pin socket at the end with 5V power and ground, as well as RX, TX, RTS and CTS at 3V logic levels. Useful whenever you want to communicate with a TTL serial device such as an Arduino Pro Mini or ESP breakout, and the pinout will match up exactly to any 'FTDI' 6-pin header.
Delivery within 2-3 weeks
+ −
Add to wish list
Assembled DC Motor + Stepper FeatherWing Add-on
US$32.60
This is the Fully assembled (with headers) DC Motor + Stepper FeatherWing which will let you use 2 x bi-polar stepper motors or 4 x brushed DC motors (or 1 stepper and 2 DC motors). Using our Feather Stacking Headers or Feather Female Headers you can connect a FeatherWing on top or bottom of your Feather board and let the board take flight!
In stock
+ −
Add to wish list
Adafruit Feather M0 with RFM95 LoRa Radio - 900MHz - RadioFruit
US$48.91
This is the Adafruit Feather M0 RFM95 LoRa Radio (900MHz). We call these RadioFruits, our take on an microcontroller with a "Long Range (LoRa)" packet radio transceiver with built in USB and battery charging. Its an Adafruit Feather M0 with a 900MHz radio module cooked in! Great for making wireless networks that are more flexible than Bluetooth LE and without the high power requirements of WiFi.
In stock
+ −
Add to wish list
Adafruit PDM Microphone Breakout with JST SH Connector
US$7.63
The first thing to note is that this sensor does not provide an 'analog' output like many of our electret microphone assemblies. So it's great for chips that do not have analog inputs. Secondly, the digital interface is a very simplistic pulse density modulation output. It's digital but its notPWM and it's not I2S. You will need to make sure your chip has a PDM interface - most 32-bit processors these days do!
In stock
+ −
Add to wish list
Adafruit Perma-Proto 40-Pin Raspberry Pi Breadboard PCB Kit - with 2x20 Header
US$12.25
It has the Cobbler baked right in. Simply solder the 2x20 box header in, and you get all the labeled breakouts with tons of prototyping space, power rails, mounting holes and that gorgeous silk. This version is for modern Raspberry Pi computers with 2x20 connectors such as the Pi B+, A+, 2, 3, 4, Zero, etc!
In stock
+ −
Add to wish list
Adafruit Perma-Proto 40-Pin Raspberry Pi Half-Size PCB Kit - with 2x20 Header
US$9.17
This product has the Cobbler baked right in. Simply solder the 2x20 box header in, and you get all the labeled breakouts with extra prototyping space, power rails, mounting holes and that gorgeous silk. This version is for modern Raspberry Pi computers with 2x20 connectors such as the Pi B+, A+, 2, 3, 4, Zero, etc!
In stock
+ −
Add to wish list
Adafruit AirLift FeatherWing – ESP32 WiFi Co-Processor
US$19.95
Give your Feather project a lift with the Adafruit AirLift FeatherWing - a FeatherWing that lets you use the powerful ESP32 as a WiFi co-processor. You probably have your favorite Feather (like the Feather M4) that comes with its own set of awesome peripherals and lots of libraries. But it doesn't have WiFi built in! So lets give that chip a best friend, the ESP32. This chip can handle all the heavy lifting of connecting to a WiFi network and transferring data from a site, even if its using the latest TLS/SSL encryption (it has root certificates pre-burned in).
Delivery within 2-3 weeks
+ −
Add to wish list
USB C to USB C Cable - USB 3.1 Gen 4 with E-Mark - 1 meter long
US$15.33
As technology changes and adapts, so does Adafruit! Rather than the regular USB A, this cable has USB C to USB C plugs! USB C is the latest industry-standard connector for transmitting data and power. Like Lightning and MagSafe cables, USB C has no up or down orientation. And who among us has inserted USB correctly the first time? Works great with any device that has a USB C port.
In stock
+ −
Add to wish list
Adafruit MCP9600 I2C Thermocouple Amplifier - K, J, T, N, S, E, B and R Type T
US$22.34
Thermocouples are very sensitive, requiring a good amplifier with a cold-compensation reference. The Adafruit MCP9600 does all that for you, and can be easily interfaced with any microcontroller or single-board-computer with I2C. Inside, the chip handles all the analog stuff for you, and can interface with just about any thermocouple type: K, J, T, N, S, E, B and R type are all supported! You can also set various alerts for over/under temperature, and read the thermocouple (hot) temperature and the chip (cold) temperature. All this over common I2C.
In stock
+ −
Add to wish list
Adafruit Prop-Maker FeatherWing
US$15.33
The Adafruit Feather series gives you lots of options for a small, portable, rechargeable microcontroller board. Perfect for fitting into your next prop build! This FeatherWing will unlock the prop-maker inside all of us, with tons of stuff packed in to make sabers & swords, props, toys, cosplay pieces, and more. We looked at hundreds of prop builds, and thought about what would make for a great low-cost (but well-designed) add-on for our Feather boards.
Delivery within 2-3 weeks
+ −
Add to wish list
Assembled Adafruit Prop-Maker FeatherWing
US$16.73
The Adafruit Feather series gives you lots of options for a small, portable, rechargeable microcontroller board. Perfect for fitting into your next prop build! This FeatherWing will unlock the prop-maker inside all of us, with tons of stuff packed in to make sabers & swords, props, toys, cosplay pieces, and more. This version of the FeatherWing has plain headers soldered in, so it's easy to plug into our Feathers. We looked at hundreds of prop builds, and thought about what would make for a great low-cost (but well-designed) add-on for our Feather boards.
In stock
+ −
Add to wish list
Adafruit Quad Side-By-Side FeatherWing Kit with Headers
US$15.33
This is the FeatherWing Quad Side-by-Side - a prototyping add-on and more for all Feather boards. This is similar to our FeatherWing Proto (2884-ADA) except there are four! The magic of the Quad comes when you want to connect your Feather to three other Feather Wings without needing any stacking headers! The Quad comes with: 1 Quad Side-by-side Wing PCB, 4 sets Feather Female Headers.
In stock
+ −
Add to wish list
Adafruit Quad 2x2 FeatherWing Kit with Headers
US$15.33
This is the FeatherWing Quad 2x2 - a prototyping add-on and more for all Feather boards. This is similar to our FeatherWing Proto (2884-ADA) except there are four! The magic of the Quad comes when you want to connect your Feather to three other Feather Wings without needing any stacking headers. The boards are all set up in a 2x2 grid, thus the name The Quad comes with: 1 Quad 2x2 Wing PCB, 4 sets Feather Female Headers.
In stock
+ −
Add to wish list
2.13" Flexible Monochrome eInk / ePaper Display - 212x104 Monochrome
US$26.95
This display is true E-Ink / E-Paper, once an image is displayed it will stay even once you remove all power. The image is also high contrast and very daylight readable. It really does look just like printed paper! This flexible display sports a 2.13" monochrome (black and white) display. It has 212x104 black ink pixels on a white-ish background. This is the same resolution as the 2.13" Tri-Color display, but doesn't have a red ink layer. The monochrome displays also take a lot less time to update, only a couple seconds instead of 15 seconds.
In stock
+ −
Add to wish list
Adafruit INA260 High or Low Side Voltage, Current, Power Sensor
US$16.15
This breakout board may well be the last current sensing solution you ever need to buy. Not only can it do the work of two multimeters, but it can do it with amazing precision and flexibility. With it you can measure high or low side DC current, the bus voltage, and have it automatically calculate the power. It can do so over impressive voltage, current, and temperature ranges with better than 1% accuracy, all while delivering the data in an easy to use format over I2C.
Delivery within 2-3 weeks
+ −
Add to wish list
Adafruit HUZZAH32 – ESP32 Breakout Board
US$19.06
This breakout is basically the 'big sister' of our HUZZAH 8266, but instead of an ESP8266 it has the '32! We've pared down our popular Feather ESP32, removing the battery charger and USB-serial converter. You just get a regulator, some protection diodes, two buttons and an LED. For some projects, where price and size are at a premium, you can program this board over the 'FTDI cable' breakout when needed, and leave it alone otherwise.
Delivery within 2-3 weeks
+ −
Add to wish list
Adafruit TPL5110 Low Power Timer Breakout
US$7.63
The Adafruit TPL5110 Power Timer is a stand-alone breakout that will turn any electronics into low-power electronics! It will take care of turning your project on/off using a built in timer that can vary from once every 100ms up to once every two hours. Basically, the TPL will turn on periodically, adjustable by potentiometer or resistor, and turn on your project's power. It will then wait until a signal is received from the project to tell the TPL that it can safely turn off the power. If the TPL does not receive a signal by the set time-out, it will reset the device like a watchdog timer.
In stock
+ −
Add to wish list
Adafruit TPL5111 Low Power Timer Breakout
US$9.17
The Adafruit TPL5111 Low Power Reset Timer is a stand-alone breakout that will turn any electronics into low-power electronics! It will take care of enabling & disabling your electronics using a built in timer that can vary from once-every 100ms up to once every two hours. Basically, the TPL will set an enable pin high periodically, adjustable by potentiometer or resistor, and turn on your project's power. It will then wait until a signal is received from the project to tell the TPL that it can safely disable the project by setting the enable pin low. If the TPL does not receive a signal by the set time-out, it will reset the device like a watchdog timer.
In stock
+ −
Add to wish list
TV-B-Gone Kit - Universal v1.2
US$29.95
The TV-B-Gone is a kit that, when soldered together, allows you to turn off almost any television within 150 feet or more.  It works on over 230 total power codes - 115 American/Asian and another 115 European codes.  You can select which zone you want during kit assembly. This is an unassembled kit which means that soldering is required - but it’s very easy and a great introduction to soldering in general.  The kit’s powered by 2x AA batteries - that aren’t included - and the output comes from 2x narrow beam IR LEDs and 2x wide-beam IR LEDs.
In stock
+ −
Add to wish list
ADXL343 - Triple-Axis Accelerometer (+-2g/4g/8g/16g) w/ I2C/SPI
US$9.17
Analog Devices has followed up on their popular classic, the ADXL345, with this near-drop-in-replacement, the ADXL343. Like the original, this is a triple-axis accelerometer with digital I2C and SPI interface breakout. It has a wide sensitivity range and high resolution, operating with an 10 or 13-bit internal ADC. Built-in motion detection features make tap, double-tap, activity, inactivity, and free-fall detection trivial. There's two interrupt pins, and you can map any of the interrupts independently to either of them.
In stock
+ −
Add to wish list
RJ-45 Ethernet Round Panel Mount Adapter Plug
US$9.17
If you need to add a panel-mount connection for Ethernet, but don't have the time or ability to cut a custom oval or square hole, this RJ-45 Ethernet Round Panel Mount Plug is the easiest and fastest way to panel-ify your existing Ethernet kit. It's about 30mm in diameter, so you can drill a hole in your wood, plastic or metal with a common hole-saw or bit, no special shapes or filing required. Un-screw the plastic nut, insert the plug and re-attach. Ta-da! Now you have two RJ45's on either side for connecting any cable.
Delivery within 2-3 weeks
+ −
Add to wish list
HDMI Round Panel Mount Plug
US$9.17
If you need to add a panel-mount connection for HDMI, but don't have the time or ability to cut a custom oval or square hole, this HDMI Round Panel Mount Plug is the easiest and fastest way to panel-ify your existing HDMI kit. It's about 30mm in diameter, so you can drill a hole in your wood, plastic or metal with a common hole-saw or bit, no special shapes or filing required. Un-screw the plastic nut, insert the plug and re-attach. Ta-da! Now you have two HDMI sockets on either side for connecting any cable.
In stock
+ −
Add to wish list
Adafruit ADXL343 + ADT7410 Sensor FeatherWing
US$18.41
Upgrade any Feather board with motion and precision temperature sensing, with this all-in-one sensing FeatherWing. It sports two fantastic sensors from Analog Devices: an ADXL343 triple-axis accelerometer and an ADT7410 precision temperature sensor. Both sensors are connected over the shared I2C bus, so you can use it with any and all Feathers! We also break out the interrupt pins and address-selection jumpers in case you want multiple Feathers or have I2C address conflicts. We've got both Arduino (C/C++) and CircuitPython libraries available so you can use it with any Feather board and get data readings in under 5 minutes.
In stock
+ −
Add to wish list
Adafruit RFM96W LoRa Radio Transceiver Breakout - 433 MHz - RadioFruit
US$30.73
Sending data over long distances is like magic, and now you can be a magician with this range of powerful and easy-to-use radio modules. Sure, sometimes you want to talk to a computer (a good time to use WiFi) or perhaps communicate with a Phone (choose Bluetooth Low Energy!) but what if you want to send data very far? Most WiFi, Bluetooth, Zigbee and other wireless chipsets use 2.4GHz, which is great for high speed transfers. If you aren't so concerned about streaming a video, you can use a lower license-free frequency such as 433 or 900 MHz. You can't send data as fast but you can send data a lot farther.'
In stock
+ −
Add to wish list
Adafruit RFM95W LoRa Radio Transceiver Breakout - 868 or 915 MHz - RadioFruit
US$30.73
Sending data over long distances is like magic, and now you can be a magician with this range of powerful and easy-to-use radio modules. Sure, sometimes you want to talk to a computer (a good time to use WiFi) or perhaps communicate with a Phone (choose Bluetooth Low Energy!) but what if you want to send data very far? Most WiFi, Bluetooth, Zigbee and other wireless chipsets use 2.4GHz, which is great for high speed transfers. If you aren't so concerned about streaming a video, you can use a lower license-free frequency such as 433 or 900 MHz. You can't send data as fast but you can send data a lot farther.'
Delivery within 2-3 weeks
+ −
Add to wish list
Adafruit CharliePlex LED Matrix Bonnet - 8x16 Warm White LEDs
US$21.49
You won't be able to look away from the mesmerizing patterns created by this Adafruit CharliePlex LED Matrix Display Bonnet.  This 16x8 LED display can be placed atop any Raspberry Pi computer with a 2x20 connector, for a beautiful, bright grid of 128 charlieplexed LEDs. It even comes with a built-in charlieplex driver that is run over I2C. We carry these Bonnets in a few vivid colors - this is the warm white LED matrix.
In stock
+ −
Add to wish list
Adafruit CharliePlex LED Matrix Bonnet - 8x16 Cool White LEDs
US$21.49
You won't be able to look away from the mesmerizing patterns created by this Adafruit CharliePlex LED Matrix Display Bonnet.  This 16x8 LED display can be placed atop any Raspberry Pi computer with a 2x20 connector, for a beautiful, bright grid of 128 charlieplexed LEDs. It even comes with a built-in charlieplex driver that is run over I2C. We carry these Bonnets in a few vivid colors - this is the cool white LED matrix.
Delivery within 2-3 weeks
+ −
Add to wish list
Adafruit CharliePlex LED Matrix Bonnet - 8x16 Green LEDs
US$19.95
You won't be able to look away from the mesmerizing patterns created by this Adafruit CharliePlex LED Matrix Display Bonnet.  This 16x8 LED display can be placed atop any Raspberry Pi computer with a 2x20 connector, for a beautiful, bright grid of 128 charlieplexed LEDs. It even comes with a built-in charlieplex driver that is run over I2C. We carry these Bonnets in a few vivid colors - this is the green LED matrix.
In stock
+ −
Add to wish list
Adafruit CharliePlex LED Matrix Bonnet - 8x16 Blue LEDs
US$19.95
You won't be able to look away from the mesmerizing patterns created by this Adafruit CharliePlex LED Matrix Display Bonnet.  This 16x8 LED display can be placed atop any Raspberry Pi computer with a 2x20 connector, for a beautiful, bright grid of 128 charlieplexed LEDs. It even comes with a built-in charlieplex driver that is run over I2C. We carry these Bonnets in a few vivid colors - this is the blue LED matrix.
In stock
+ −
Add to wish list
Adafruit CharliePlex LED Matrix Bonnet - 8x16 Yellow LEDs
US$19.95
You won't be able to look away from the mesmerizing patterns created by this Adafruit CharliePlex LED Matrix Display Bonnet.  This 16x8 LED display can be placed atop any Raspberry Pi computer with a 2x20 connector, for a beautiful, bright grid of 128 charlieplexed LEDs. It even comes with a built-in charlieplex driver that is run over I2C. We carry these Bonnets in a few vivid colors - this is the yellow LED matrix.
In stock
+ −
Add to wish list
Adafruit USB C Breakout Board - Downstream Connection
US$4.55
Throw out all those Mini and Micro B USB cables you have in a plastic bin - the next generation of USB connectors is here with USB C! You will start to see these connectors pop up on all sorts of devices, as the industry moves from micro B or lightening to the new standard.
In stock
+ −
Add to wish list
1 2 3 4 5 6