Adafruit

1 2 3 4 5 6 7 8
2 - 16
US$1.29
Plugs in nicely with our Li-Poly batteries, it even has the right color coding!
In stock
+
Add to wish list

US$1.32
977 Adafruit TO-220 Clip-On Heatsink Get the most out of your regulators, transistors and other TO-220 packaged chips by clipping on a heat-sink. Your...
In stock
+
Add to wish list

US$1.32
Add a micro-slice standard solderless breadboard to your Perma-Proto or other perf-board. This 2x4 point solder-less breadboard is a good way to add some solderless prototyping space if you just need to have a couple points.
In stock
+
Add to wish list

US$1.32
These 2-wire cables are 16cm long and come as a set.  One side has a 2-pin JST SM type connector plug on the end.  The other side has a matching 2-pin JST SM type receptacle connector.  They are good for whenever you have 2 wires you want to be able to plug and unplug.
In stock
+
Add to wish list

US$1.49
This cable will let you turn a JST PH 3-pin cable socket into 3 individual tinned wires. These are great to match up with our JST 3-PH cables, for extending and connecting sensors or LEDs, and the wires are even color coded!
In stock
+
Add to wish list

US$1.49
This cable will let you turn a JST PH 3-pin cable socket into 4 individual tinned wires. These are great to match up with our JST 4-PH cables, for extending and connecting sensors or LEDs, and the wires are even color coded!
In stock
+
Add to wish list

US$1.67
Red and black tinned wires with a 2-pin JST PH connector on the end. 4" / 100mm long. Matches up nicely with our Lipoly charger!
In stock
+
Add to wish list

US$1.67
This power jack is designed to fit 2.1mm power plugs snugly and securely. Perfect for adding a power connector to your project. We went for the more expensive "thin pin" type which snap into breadboards or perfboards.
In stock
+
Add to wish list

US$1.67
This potentiometer is a two-in-one, good in a breadboard or with a panel. Its a fairly standard linear taper 10K ohm potentiometer, with a grippy shaft. Its smooth and easy to turn, but not so loose that it will shift on its own.
In stock
+
Add to wish list

US$1.67
These small sticky bumpers are our favorite accessory for any electronic kit or device. They are sticky, but not impossible to remove. They're small enough to fit onto any board, and have just enough height to give clearance to thru-hole soldered components.
In stock
+
Add to wish list

US$1.67
Make your own USB connections without slicing apart a USB cable and soldering those thin wires inside. These DIY "USB shells" are available in USB A plug, micro B, and USB A socket. 
In stock
+
Add to wish list

US$1.67
Make your own USB connections without slicing apart a USB cable and soldering those thin wires inside. These DIY "USB shells" are available in USB A plug, micro B, and mini B.
In stock
+
Add to wish list

US$1.67
These spring-vibration switches are high sensitivity non-directional vibration induced trigger switches.
In stock
+
Add to wish list

US$1.67
Add a micro-slice standard solderless breadboard to your Perma-Proto or other perf-board. This 2x8 point solder-less breadboard is a good way to add some solderless prototyping space if you just need to have a couple points.
In stock
+
Add to wish list

US$1.67
2.1mm inner diameter (5.5mm outer diameter) is the most common type of DC plug, but you can use this adapter for anything else that has a 1.3mm ID (3.5mm OD) DC jack!
In stock
+
Add to wish list

US$1.68
The 5462-ADA is a 50mm 18 pin connector.
In stock
+
Add to wish list
1 2 3 4 5 6 7 8
2 - 16