Adafruit

US$34.92
This pi plate is perfect for when you want to build a stand-alone project with its own user interface. The 4 directional buttons plus select button allows basic control without having to attach a bulky computer.
In stock
+
Add to wish list

US$1.75
XBees are so cute and tiny but if you're using them in a circuit you'll be annoyed to find that your classic 0.1" headers don't fit them! That's because they use 2mm spacing instead of 2.54mm spacing. That's why you need a special socket like this one.
In stock
+
Add to wish list

US$23.03
This solenoid in particular is nice and strong, with a 40mm long body and a 'captive' armature with a return spring. This means that when activated with up to 12VDC, the solenoid moves and then the voltage is removed it springs back to the original position, which is quite handy. Many lower cost solenoids are only push type or only pull type and may not have a captive armature (it'll fall out!) or don't have a return spring. This solenoid has 4xM3 (metric) threaded holes in the bottom for easy mounting.
In stock
+
Add to wish list

US$6.25
This order comes with 5 Royal Blue "1206 size" LEDs, matched with a 100 ohm resistor.
In stock
+
Add to wish list

US$10.42
These chrome-plated metal buttons are rugged and look real good while doing it! Simply drill a 16mm hole into any material up to 1/2" thick and you can fit these in place, there's even a rubber gasket to keep water out of the enclosure. On the front of the button is a flat metal actuator, surrounded by a green plastic LED ring. On the back there are 3 contacts for the button (common, normally-open and normally-closed) and 2 for the green LED ring (+ and -). Connect 3 to 6V to the LED to have it light up nicely, there's a built in resistor! If you want to use this with a higher voltage, say 12V or 24V, simply add a 470 ohm resistor in series with the LED connection to keep the LED current at around 20mA.
In stock
+
Add to wish list

US$6.92
This is a 9V battery pack with on/off switch and a pre-attached 5.5mm/2.1mm barrel plug. Use this to battery-power your Arduino (or other electronic projects) - it's ready to go out of the box!
In stock
+
Add to wish list

US$11.46
This 60mm diameter arcade button is large and inviting and ready for all sorts of pressing and pushing. We've seen these on some games of skill in arcades, they're easy to mount on nearly any kind of enclosure. They're not waterproof or weatherproof, so best used indoors. 
Delivery within 2-3 weeks
+
Add to wish list

US$2.18
What do they do? They stack. Put the headers through your Feather and then you can not only plug them into a solderless breadboard, but you could attach circuitry on top as well.
In stock
+
Add to wish list

US$6.92
This order comes with 5 Ruby Red "1206 size" LEDs, matched with a 220 ohm resistor.
In stock
+
Add to wish list

US$12.17
This proto-board is the PCB you always wish you had, but never realized it! We took the basic layout of a full-sized breadboard (the PCB has 60 rows instead of 63 rows) and turned that into a beautiful PCB.
In stock
+
Add to wish list

US$4.75
One cable per order. The ribbon cable is 0.06mm/0.025" pitch and the connector is a 1.27mm (0.05") pitch 2x5 box. These are not for use with programming most AVRs or other large devices that have 0.1" pitch connectors so be aware which you need!
Delivery within 2-3 weeks
+
Add to wish list

US$1.74
Silicone-sheathing wire is super-flexible and soft, and its also strong! Able to handle up to 200°C and up to 600V, it will do when PVC covered wire wimps out.
In stock
+
Add to wish list

US$10.42
This button is an on/off switch button, when you press it the 'normally-open' contact shorts to the common contact and the button stays 'pressed'. When you press it a second time, the button springs open, and the contacts open up again. 
In stock
+
Add to wish list

US$78.67
Featuring a 2.8" display with 320x240 16-bit color pixels and a single-touch capacitive touch overlay. The plate uses the high speed SPI interface on the Pi and can use the mini display as a console, X window port, displaying images or video etc. Best of all it plugs right in on top!
In stock
+
Add to wish list

US$4.38
This 4" / 100mm long flexible uFL 2.4GHz antenna has approx 4DBi gain and a 50Ω impedance so it will work fantastically with just about any 2.4-2.5GHz wireless receiver/transmitter such as the Adafruit CC3000s! Antenna comes with a uFL (a.k.a u.FL / IPX / IPEX) connector, so no more need for additional adapters to get your IoT cloud flying high!
Delivery within 2-3 weeks
+
Add to wish list