Adafruit

CA$46.95

Add a typing interface to your project with this microcontroller-friendly miniature keyboard. We found the smallest PS/2+USB keyboard available, a mere 8.75" x 4.65" x 0.6" (220mm x 118mm x 16mm)! It's small but usable to make a great accompaniment to either a microcontroller project or a computer such as the Beagle Bone or Raspberry Pi.

Delivery within 2-3 weeks
+
Add to wish list

CA$13.37
Trinket may be small, but do not be fooled by its size! It's a tiny microcontroller board, built around the Atmel ATtiny85, a little chip with a lot of power. We wanted to design a microcontroller board that was small enough to fit into any project, and low cost enough to use without hesitation. ATtiny85 on-board, 8K of flash, 512 byte of SRAM, 512 bytes of EEPROM.
In stock
+
Add to wish list

CA$2.74
If you need to connect a battery pack or wired power supply to a board that has a DC jack - this adapter will come in very handy! There is a 2.1mm DC plug on one end, and a screw terminal block on the other.
In stock
+
Add to wish list

CA$9.53
This set comes with 3 different boards which fit 5 different packages and comes with five SOT-23 (fits 2 x SOT-23 on the back, and a single SOT-23-5 or SOT-23-6 on the front), four SOT-89 or SOT-223, and four TO-252.
Delivery within 2-3 weeks
+
Add to wish list

CA$33.66
Turn any surface/wall/table etc into a speaker with a surface transducer. This type of speaker does not have a moving cone like most speakers you've seen. Instead, a metal rod is wrapped with the voice coil.
Delivery within 2-3 weeks
+
Add to wish list

CA$38.40
This Japanese upgrade to the classic $5 solder sucker is a joy to use. Since the tip is rubbery soft silicone you don't have to worry about it melting. You also get a long tube in case it gets clogged or dirty.
In stock
+
Add to wish list

CA$13.46
The T-Cobbler Plus is an add on prototyping board from Adafruit specifically designed for the B+, Pi 2 and Pi 3 that can break out all those tasty power, GPIO, I2C and SPI pins from the 40-pin header onto a solderless breadboard. This set will make "cobbling together" prototypes with the Pi super easy.
In stock
+
Add to wish list

CA$152.23
Included are plenty of parts to make a few different fun projects! There's a Flora motherboard, a GPS module that can also perform location datalogging, eight ultra-bright chainable RGB pixels, a battery holder and batteries, two types of our high quality stainless steel thread, alligator clips to help you test out your parts, a USB cable for reprogramming the Flora, and some parts to make a wearable remote control (or TV-B-Gone!): NPN transistors, long range IR LEDs, and matching resistors.
In stock
+
Add to wish list

CA$15.30

15 rows of double 5-hole rows + 48 individual holes. 2 power rails with positive/negative markings. 2.1" x 1.3" (54mm x 33mm), 0.063" thick FR4. 1.2mm / 0.047" drill holes. 4 x 0.125"/3mm drill mounting holes spaced on a 45.5mm x 25.4mm / 1.8" x 1" rectangle. 

In stock
+
Add to wish list

CA$1.84
2.1mm inner diameter (5.5mm outer diameter) is the most common type of DC plug, but you can use this adapter for anything else that has a 1.3mm ID (3.5mm OD) DC jack!
In stock
+
Add to wish list

CA$23.08

This breakout AVR board is a prototype design with minimum components. We took the business-card-sized AVR target board from Evil Mad Scientist Laboratories and added a few components to make an AVR dev board that has only the bare minimums!

In stock
+
Add to wish list

CA$11.54
65 flexible stranded core wires with stiff ends molded on in red, orange, yellow, green, blue, brown, black and white. These are a major improvement over the "box of bent wires" that are sometimes sold with breadboards, and faster than stripping your own solid core wires. Makes breadboarding super fast.
In stock
+
Add to wish list

CA$9.53
This A/V RCA Cable for Raspberry Pi is a great way to turn your Pi 2, A+ or B+'s output into a full on composite video and audio device.  Simply connect the cable to your Raspberry Pi's 3.5mm jack and the other side into whatever device you're looking to connect to and get full RCA visuals and sound.
In stock
+
Add to wish list

CA$28.76
Timing belts are a fantastic way to transfer rotational motion (from a stepper motor) into linear motion (along a rail) and these GT2 belts are excellent for the task. 
In stock
+
Add to wish list

CA$3.37
They're what you see on the back of nearly every synthesizer and drum machine. These are nice sturdy jacks, and breadboard-friendly, with all the pins on 0.1" spacing for easy wiring.
In stock
+
Add to wish list