Our Brands

Adafruit

1 2 3 4 5 6 7 8 9 10 11 12 13
7 - 21
Sort by Popularity: Low to High
15 Per Page
Adafruit Quad Side-By-Side FeatherWing Kit with Headers
US$15.33
This is the FeatherWing Quad Side-by-Side - a prototyping add-on and more for all Feather boards. This is similar to our FeatherWing Proto (2884-ADA) except there are four! The magic of the Quad comes when you want to connect your Feather to three other Feather Wings without needing any stacking headers! The Quad comes with: 1 Quad Side-by-side Wing PCB, 4 sets Feather Female Headers.
In stock
+ −
Add to wish list
STEMMA QT / Qwiic JST SH 4-Pin Cable - 50mm Long
US$1.79
This 4-wire cable is 50mm / 1.9" long and fitted with JST SH female 4-pin connectors on both ends. Compared with the chunkier JST PH these are 1mm pitch instead of 2mm, but still have a nice latching feel, while being easy to insert and remove.
In stock
+ −
Add to wish list
JST PH 4-pin Vertical Connector (10-pack) - STEMMA
US$5.49
Designing boards with plug-n-play connectivity is a snap, with STEMMA connectors. Here's a pack of 10 of our favorite 2mm pitch connector - the JST PH 4 pin. These are the vertical style.
In stock
+ −
Add to wish list
Adafruit ADXL343 + ADT7410 Sensor FeatherWing
US$18.41
Upgrade any Feather board with motion and precision temperature sensing, with this all-in-one sensing FeatherWing. It sports two fantastic sensors from Analog Devices: an ADXL343 triple-axis accelerometer and an ADT7410 precision temperature sensor. Both sensors are connected over the shared I2C bus, so you can use it with any and all Feathers! We also break out the interrupt pins and address-selection jumpers in case you want multiple Feathers or have I2C address conflicts. We've got both Arduino (C/C++) and CircuitPython libraries available so you can use it with any Feather board and get data readings in under 5 minutes.
In stock
+ −
Add to wish list
CAP1188 - 8-Key Capacitive Touch Sensor Breakout - I2C or SPI
US$13.92
Add lots of touch sensors to your next microcontroller project with this easy-to-use 8-channel capacitive touch sensor breakout board, starring the CAP1188. This chip can handle up to 8 individual touch pads, and has a very nice feature that makes it stand out for us: it will light up the 8 onboard LEDs when the matching touch sensor fires to help you debug your sensor setup.
Delivery within 2-3 weeks
+ −
Add to wish list
Adafruit Mini PiTFT 1.3" - 240x240 TFT Add-on for Raspberry Pi
US$22.95
This product is your little TFT pal, ready to snap onto any and all Raspberry Pi computers, to give you a little display. The Mini PiTFT comes with a full color 240x240 pixel IPS display with great visibility at all angles. The TFT uses only the SPI port so its very fast, and we leave plenty of pins remaining available for buttons, LEDs, sensors, etc. It's also nice and compact so it will fit into any case.
In stock
+ −
Add to wish list
Adafruit LoRa Radio Bonnet with OLED - RFM95W @ 915MHz - RadioFruit
US$45.45
Adafruit LoRa Radio Bonnet with OLED - RFM95W @ 915MHz - RadioFruit The latest Raspberry Pi computers come with WiFi and Bluetooth, and now you can add...
Delivery within 2-3 weeks
+ −
Add to wish list
STEMMA QT / Qwiic JST SH 4-Pin Cable - 200mm Long
US$1.79
This 4-wire cable is a little over 200mm / 7.8" long and fitted with JST-SH female 4-pin connectors on both ends. Compared with the chunkier JST-PH these are 1mm pitch instead of 2mm, but still have a nice latching feel, while being easy to insert and remove.
In stock
+ −
Add to wish list
Assembled Adafruit Feather M0 WiFi - ATSAMD21 + ATWINC1500
US$56.95
Feather is the new development board from Adafruit, and like its namesake, it is thin, light, and lets you fly! We designed Feather to be a new standard for portable microcontroller cores. This is the Assembled Adafruit Feather M0 WiFi w/ATWINC1500 - our take on an 'all-in-one' Arduino-compatible + high speed, reliable WiFi with built in USB and battery charging. Its an Adafruit Feather M0 with a WiFi module.
In stock
+ −
Add to wish list
Adafruit LPS33HW Water Resistant Pressure Sensor - STEMMA QT
US$17.52
Sometimes you need to sense pressure in a damp or caustic environment. And sometimes you need to know the relative changes in pressure as well as the absolute pressure. For the times you need to do both (or either), the LPS33HW is the pressure sensor for you. Combining protection from water intrusion with support for high precision relative and absolute measurements, this sensor will do what you need.
In stock
+ −
Add to wish list
Adafruit Prop-Maker FeatherWing
US$15.33
The Adafruit Feather series gives you lots of options for a small, portable, rechargeable microcontroller board. Perfect for fitting into your next prop build! This FeatherWing will unlock the prop-maker inside all of us, with tons of stuff packed in to make sabers & swords, props, toys, cosplay pieces, and more. We looked at hundreds of prop builds, and thought about what would make for a great low-cost (but well-designed) add-on for our Feather boards.
Delivery within 2-3 weeks
+ −
Add to wish list
Adafruit LPS22 Pressure Sensor - STEMMA QT / Qwiic - LPS22HB
US$10.45
This absolute pressure sensor, ST LPS22HB (a.k.a LPS22) can quickly and easily measure this air pressure, useful when you want to know about the weather (are we in a low-pressure or high-pressure system?) or to determine altitude, as the air thins out the higher we get above sea level.
In stock
+ −
Add to wish list
Adafruit e-Ink Feather Friend with 32KB SRAM
US$13.79
We've liked these displays for a long time, and we've got Arduino/CircuitPython drivers for all of our Feathers, so wouldn't an e-paper Feather Friend make a ton of sense? Luckily for us, just about every small-medium size EInk display made these days has a standard 24-pin connection. This Friend will add all the power supply support circuitry and level shifting so you can attach your favorite display (up to tri-color 4.2") and wire it up to your favorite development board.
In stock
+ −
Add to wish list
FTDI Serial TTL-232 USB Type C Cable - 3V Power and Logic
US$30.73
This is a USB C to TTL serial cable with an FTDI FT232R usb/serial chip embedded in the head. It has a 6-pin socket at the end with 5V power and ground, as well as RX, TX, RTS and CTS at 3V logic levels. Useful whenever you want to communicate with a TTL serial device such as an Arduino Pro Mini or ESP breakout, and the pinout will match up exactly to any 'FTDI' 6-pin header.
Delivery within 2-3 weeks
+ −
Add to wish list
USB C to USB C Cable - USB 3.1 Gen 4 with E-Mark - 1 meter long
US$15.33
As technology changes and adapts, so does Adafruit! Rather than the regular USB A, this cable has USB C to USB C plugs! USB C is the latest industry-standard connector for transmitting data and power. Like Lightning and MagSafe cables, USB C has no up or down orientation. And who among us has inserted USB correctly the first time? Works great with any device that has a USB C port.
In stock
+ −
Add to wish list
1 2 3 4 5 6 7 8 9 10 11 12 13
7 - 21