Adafruit

1 2 3 4 5 6 7 8 9 10 11
5 - 19
US$1.79
This 4-wire cable is 50mm / 1.9" long and fitted with JST SH female 4-pin connectors on both ends. Compared with the chunkier JST PH these are 1mm pitch instead of 2mm, but still have a nice latching feel, while being easy to insert and remove.
Delivery within 1-2 weeks
+
Add to wish list

US$4.99
This cable will make it super easy to use our plug-and-play STEMMA QT boards with boards like Circuit Playground. On one end you get a Qwiic / STEMMA QT connector (technically known as a JST SH 4-pin plug) into 4 individual wires with grippy alligator clips. We're carrying these to match up with our boards or breakouts with 'STEMMA QT' connectors on them.
In stock
+
Add to wish list

US$2.49
This cable will let you turn a JST PH 4-pin cable port into 4 individual wires with high-quality 0.1" female sockets on the end. We're carrying these to match up with any of our boards with 'STEMMA' connectors on them.
In stock
+
Add to wish list

US$2.49
These 3-wire cables are 163mm (6.4") long and come as a set. One cable has a JST SM type connector plug on the end. The other cable has a matching JST SM type receptacle connector. They are good for whenever you have 3 wires you want to be able to plug and unplug.
In stock
+
Add to wish list

US$1.89
This 4-wire cable is a little over 150mm / 6" long and fitted with JST-SH female 4-pin connectors on one end and premium Dupont male headers on the other. Compared with the chunkier JST-PH these are 1mm pitch instead of 2mm, but still have a nice latching feel, while being easy to insert and remove.
In stock
+
Add to wish list

US$30.44
This miniature GPS breakout is only 1" x 1" (~ 25mm x 25mm) but houses a complete GPS/GNSS solution with both I2C and UART interfaces. There's even an antenna on top so it's plug and play!
In stock
+
Add to wish list

US$13.79
Inside are two sensors, one is a classic 3-axis accelerometer, which can tell you which direction is down towards the Earth (by measuring gravity). The other is a magnetometer that can sense where the strongest magnetic force is coming from, generally used to detect magnetic north. By combining this data you can then orient your project!
Delivery within 1-2 weeks
+
Add to wish list

US$10.95
Inside are two sensors, one is a classic 3-axis accelerometer, which can tell you which direction is down towards the Earth (by measuring gravity). The other is a gyroscoe that can sense how fast the board is being twisted around. By combining this data you can tell how your project is moving through space
In stock
+
Add to wish list

US$1.49
This cable will let you turn a JST PH 3-pin cable socket into 4 individual tinned wires. These are great to match up with our JST 4-PH cables, for extending and connecting sensors or LEDs, and the wires are even color coded!
In stock
+
Add to wish list

US$30.95
This is a USB C to TTL serial cable with an FTDI FT232R usb/serial chip embedded in the head. It has a 6-pin socket at the end with 5V power and ground, as well as RX, TX, RTS and CTS at 3V logic levels. Useful whenever you want to communicate with a TTL serial device and the pinout will match up exactly to any 'FTDI' 6-pin header.
In stock
+
Add to wish list

US$15.45
This lovely little display breakout is the best way to add a small, colorful and very bright display to any project. Since the display uses 4-wire SPI to communicate and has its own pixel-addressable frame buffer, it can be used with every kind of microcontroller. Even a very small one with low memory and few pins available! The 1.14" display has 240x135 16-bit full color pixels and is an IPS display, so the color looks great up to 80 degrees off axis in any direction.
Delivery within 1-2 weeks
+
Add to wish list

US$2.39
These 5-wire cables are 168mm (6.6") long and come as a set. One cable has a JST SM type connector plug on the end. The other cable has a matching JST SM type receptacle connector. They are good for whenever you have 5 wires you want to be able to plug and unplug.
In stock
+
Add to wish list

US$2.39
These 6-wire cables are 162mm (6.4") long and come as a set. One cable has a JST SM type connector plug on the end. The other cable has a matching JST SM type receptacle connector. They are good for whenever you have 6 wires you want to be able to plug and unplug.
In stock
+
Add to wish list

US$1.29
Plugs in nicely with our Li-Poly batteries, it even has the right color coding!
In stock
+
Add to wish list

US$1.49
This cable will let you turn a JST PH 3-pin cable socket into 3 individual tinned wires. These are great to match up with our JST 3-PH cables, for extending and connecting sensors or LEDs, and the wires are even color coded!
In stock
+
Add to wish list
1 2 3 4 5 6 7 8 9 10 11
5 - 19