Our Brands

Adafruit

1 2 3 4 5 6 7 8 9 10 11
5 - 19
Sort by Popularity: Low to High
15 Per Page
4503-ADA, Adafruit LSM6DS3TR-C 6-DoF Accel + Gyro IMU - STEMMA QT / Qwiic
US$16.33
Le 4503-ADA est une carte de dérivation pour capteur d'accéléromètre et de gyroscope.
In stock
+ −
Add to wish list
4062-ADA Adafruit Feather nRF52840 Express
US$36.35
This chip has twice the flash, and four times the SRAM of its earlier sibling, the nRF52832 - 1 MB of FLASH and 256KB of SRAM. Compared to the nRF51, this board has 4-8 times more of everything. For this chip, we've added Arduino IDE support - you can program the nRF52840 chip directly to take full advantage of the Cortex-M4 processor, and then calling into the Nordic SoftDevice radio stack when you need to communicate over BLE. Since the underlying API and peripherals are the same for the '832 and '840, you can supercharge your older nRF52832 projects with the same exact code, with a single recompile!
Delivery within 2-3 weeks
+ −
Add to wish list
5-pin JST SM Plug + Receptacle Cable Set
US$2.39
These 5-wire cables are 168mm (6.6") long and come as a set. One cable has a JST SM type connector plug on the end. The other cable has a matching JST SM type receptacle connector. They are good for whenever you have 5 wires you want to be able to plug and unplug.
In stock
+ −
Add to wish list
4500-ADA Adafruit CLUE - nRF52840 Express with Bluetooth LE
US$59.10
Get a CLUE here at Adafruit by picking up this sensor-packed development board. We wanted to build some projects that have a small screen and a lot of sensors. To make it compatible with existing projects, we made it the same shape and size as the BBC micro:bit and with the same edge-connector on the bottom with 5 big pads so it will fit into your existing robot kit or 'bit add-on.
Delivery within 2-3 weeks
+ −
Add to wish list
JST PH 3-pin Plug to Color Coded Alligator Clips Cable
US$2.99
This cable has a JST PH 3-pin on one side and alligator clips on the other, so it could be used to connect to wires or pads like that on the Circuit Playground or micro:bit.
In stock
+ −
Add to wish list
Adafruit CharliePlex LED Matrix Bonnet - 8x16 Cool White LEDs
US$21.49
You won't be able to look away from the mesmerizing patterns created by this Adafruit CharliePlex LED Matrix Display Bonnet.  This 16x8 LED display can be placed atop any Raspberry Pi computer with a 2x20 connector, for a beautiful, bright grid of 128 charlieplexed LEDs. It even comes with a built-in charlieplex driver that is run over I2C. We carry these Bonnets in a few vivid colors - this is the cool white LED matrix.
Delivery within 2-3 weeks
+ −
Add to wish list
3-pin JST SM Plug + Receptacle Cable Set
US$2.49
These 3-wire cables are 163mm (6.4") long and come as a set. One cable has a JST SM type connector plug on the end. The other cable has a matching JST SM type receptacle connector. They are good for whenever you have 3 wires you want to be able to plug and unplug.
In stock
+ −
Add to wish list
3144-ADA Large Dual Row Wire Housing Pack for DIY Jumper Cables
US$7.49

Compatible with both male and female wires, these fully customizable wire housings bring DIY to a new level, giving you near limitless options when using jumper wires in your project. This is a pack of small, dual row housings. This pack includes: 5 x 2x2 housing, 5 x 2x3 housing, 5 x 2x4 housing, 5 x 2x5 housing, 5 x 2x6 housing. 

In stock
+ −
Add to wish list
3405-ADA Adafruit HUZZAH32 – ESP32 Feather Board
US$29.80
The HUZZAH32 is an ESP32-based Feather, made with the official WROOM32 module. It has built in USB-to-Serial converter, automatic bootloader reset, Lithium Ion/Polymer charger, and just about all of the GPIOs brought out so you can use it with any of our Feather Wings.
In stock
+ −
Add to wish list
2x20 Socket Riser Header for Raspberry Pi HATs and Bonnets
US$3.17
Give yourself a lift with this 2x20 female socket header that has slightly longer than usual pins. You can plug this into your Raspberry Pi GPIO port and then plug a HAT or Bonnet or Phat on top. Especially useful for Bonnets that have slim headers on the bottom, but you want them to clear some of the components on the Pi, or fit into a case nicer.
Delivery within 2-3 weeks
+ −
Add to wish list
JST PH 3-pin Horizontal Connector (10-pack) - STEMMA
US$5.49
Designing boards with plug-n-play connectivity is a snap, with STEMMA connectors. Here's a pack of 10 of our favorite 2mm pitch connector - the JST PH 3 pin. These are the horizontal style.
In stock
+ −
Add to wish list
4516-ADA Adafruit Feather nRF52840 Sense
US$57.83
This Feather microcontroller comes with Bluetooth Low Energy and native USB support featuring the nRF52840! This Feather is an 'all-in-one' Arduino-compatible + Bluetooth Low Energy with built in USB plus battery charging. With native USB it works great with CircuitPython, too.
Delivery within 2-3 weeks
+ −
Add to wish list
JST SH 4-pin Cable with Alligator Clips - STEMMA QT / Qwiic
US$4.99
This cable will make it super easy to use our plug-and-play STEMMA QT boards with boards like Circuit Playground. On one end you get a Qwiic / STEMMA QT connector (technically known as a JST SH 4-pin plug) into 4 individual wires with grippy alligator clips. We're carrying these to match up with our boards or breakouts with 'STEMMA QT' connectors on them.
In stock
+ −
Add to wish list
JST PH 3-Pin Socket to Color Coded Cable - 200mm
US$1.49
This cable will let you turn a JST PH 3-pin cable socket into 3 individual tinned wires. These are great to match up with our JST 3-PH cables, for extending and connecting sensors or LEDs, and the wires are even color coded!
In stock
+ −
Add to wish list
USB Cable with Switch
US$5.75
Comes with a USB A socket on one end and a USB A plug on the other. In between is an in-line switch that is rated for 2 Amps. The data lines are not connected through - this is a ground/5V power switch only! The switch is on the positive 5V line.
In stock
+ −
Add to wish list
1 2 3 4 5 6 7 8 9 10 11
5 - 19