Our Brands

Adafruit

5 - 19
13 14 15 16 17 18 19 20 21 22 23 24 25 26 27
21 - 35
Sort by Popularity: Low to High
15 Per Page
816 3x4 Right Angle Male Header - 4 pack
816 3x4 Right Angle Male Header - 4 pack
US$5.17
Three rows in a right angle header!? Yes! These chunks of 0.1" header has yet-another-row - handy for when you want to connect cables that come in sets of three, like perhaps sensors, or servos. These plug into any standard 0.1" spacing perf-boards or other PCBs and work nicely with our female-ended wire sets.
Delivery within 2-3 weeks
+ −
Add to wish list
2488-ADA Adafruit METRO 328 with Headers - ATmega328
US$26.95
This is the Adafruit METRO with headers.  It comes with headers soldered on.  It's a fully assembled and tested board with through-hole headers attached.  METRO is the culmination of years of playing with AVRs: we wanted to make a development board that is easy to use and is hacker friendly. At the heart is an ATmega328P, with 32KB of flash and 2KB of RAM, running at 16 MHz.
In stock
+ −
Add to wish list
1989-ADA Adafruit Pi T-Cobbler Plus Kit - Breakout for Pi A+/B+/Pi 2/Pi 3
US$13.13
The T-Cobbler Plus is an add on prototyping board from Adafruit specifically designed for the B+, Pi 2 and Pi 3 that can break out all those tasty power, GPIO, I2C and SPI pins from the 40-pin header onto a solderless breadboard. This set will make "cobbling together" prototypes with the Pi super easy.
In stock
+ −
Add to wish list
3342-ADA 2x40 Right Angle Edge Connector for micro:bit
US$6.92
This is a connector that fits directly to the edge contacts of a BBC micro:bit. The connector has 80 pins, but because of the different widths of the micro:bit edge contacts, some of the micro:bit contacts will map to more than one of this connector's pins. Also, the back half of the pins are not used at all. The edge connector gives access to all the important pins on the bottom edge of the micro:bit. Check the datasheet for the pin spacing and orientation. This connector is best used with a custom PCB!
In stock
+ −
Add to wish list
411 2.1mm to 1.7mm DC jack adapter
411 2.1mm to 1.7mm DC jack adapter
US$4.38

We're carrying this adapter primarily to allow Chumby Hacker Board users to adapt our nice 5V @ 2A power supply to their CHB. But you can use this adapter for anything else that has a 1.7mm DC jack, such as a PSP.

In stock
+ −
Add to wish list
159 Diffused RGB (tri-color) LED - Common Anode
159 Diffused RGB (tri-color) LED - Common Anode
US$3.28
Diffused 5mm tri-color LED with separate red, green and blue LED chips inside! Nice indicator, and fun to color-swirl. 60 degree viewing angle.
In stock
+ −
Add to wish list
149-ADA Solder wick - 3S 5ft.
149-ADA Solder wick - 3S 5ft.
US$5.25
5ft spool - Used along with the solder sucker to clean up soldering messes. Wick really comes in handy when soldering or desoldering surface-mount parts. Even if you don't have the best iron for SMT work, a bit of wick will fix it up.
In stock
+ −
Add to wish list
895 Wire Light LED Strand - 12 Blue LEDs + Coin Cell Holder
895 Wire Light LED Strand - 12 Blue LEDs + Coin Cell Holder
US$8.67
Each strand comes with 12 LEDs, approximately 5cm/2 inches apart for a 2 foot long strand of wire. At one end of the magnet wire, a double stranded-core wire is soldered on and heat-shrinked to protect it.
In stock
+ −
Add to wish list
261 JST 2-pin cable
261 JST 2-pin cable
US$1.67
Red and black tinned wires with a 2-pin JST PH connector on the end. 4" / 100mm long. Matches up nicely with our Lipoly charger!
In stock
+ −
Add to wish list
575 Panel Volt Meter - 4.5V to 30VDC
575 Panel Volt Meter - 4.5V to 30VDC
US$13.92
Dimensions: 48x29x21mm. Panel cutout: 45.5mm x 26.5mm. Digit size: 14mm/0.56" high, green LEDs. Refresh rate: about 2 Hz. Power specifications: 4.5V to 30V DC measurements. 0.1V precision. 3-4mA draw. Green LED display. Reverse polarity protected.
In stock
+ −
Add to wish list
2222-ADA GPIO Header for Raspberry Pi B+ - 2x20 Female Header
US$2.63
Connect your own PCB to a Raspberry Pi B+ with this normal-height female header.
In stock
+ −
Add to wish list
978 Panel mount HDMI Cable - 40 cm
978 Panel mount HDMI Cable - 40 cm
US$10.42
This panel mount extension cable will allow you to extend an HDMI connection and secure it to an enclosure. Perfect for placing your Raspberry Pi in a secure box. Two M3 screws are used to attach the female socket end, 1"/25.4mm apart. Two hex-screws are included and the hex nuts are embedded inside the molded end. 
In stock
+ −
Add to wish list
1352-ADA 4-Way 2.1mm DC Barrel Jack Splitter
1352-ADA 4-Way 2.1mm DC Barrel Jack Splitter
US$8.67
Quadruple your power adapters with this wonderfully simple 4-way power jack splitter. All you have to do is connect a standard 5.5mm/2.1mm sized plug into one end, and behold, four identical plugs to use!
In stock
+ −
Add to wish list
2029-ADA Assembled Pi Cobbler Plus - Breakout Cable - for Pi B+/A+/Pi 2/Pi 3
US$12.17
It's an add on prototyping Pi Cobbler from Adafruit specifically designed for the B+ and Pi 2 that you can break out all those tasty power, GPIO, I2C and SPI pins from the 40-pin header onto a solderless breadboard. This will make "cobbling together" prototypes with the Pi super easy.
In stock
+ −
Add to wish list
2880-ADA 2-pin JST SM Plug + Receptacle Cable Set
US$1.32
These 2-wire cables are 16cm long and come as a set.  One side has a 2-pin JST SM type connector plug on the end.  The other side has a matching 2-pin JST SM type receptacle connector.  They are good for whenever you have 2 wires you want to be able to plug and unplug.
In stock
+ −
Add to wish list
5 - 19
13 14 15 16 17 18 19 20 21 22 23 24 25 26 27
21 - 35