Adafruit

US$5.17
Three rows!? Yes! These chunks of 0.1" header has yet-another-row - handy for when you want to connect cables that come in sets of three, like perhaps sensors, or servos. These plug into any standard 0.1" spacing perf-boards or other PCBs and work nicely with our female-ended wire sets.
In stock
+
Add to wish list

US$5.17
Three rows in a right angle header!? Yes! These chunks of 0.1" header has yet-another-row - handy for when you want to connect cables that come in sets of three, like perhaps sensors, or servos. These plug into any standard 0.1" spacing perf-boards or other PCBs and work nicely with our female-ended wire sets.
Delivery within 2-3 weeks
+
Add to wish list

US$5.17
Make a nice portable power pack with this 4 x AA battery holder. It fits any alkaline or rechargeable AA batteries in series. There's a snap on cover and an on/off switch which can be handy when wiring to something without a switch.
In stock
+
Add to wish list

US$5.17
If you want to have a nice clean board (or maybe you're doing some repair) you can use this stiff-bristled brush without worries. Some people like to drip a little rubbing alcohol on their PCBs after soldering and then scrubbing to remove rosin/flux. Finally, you have the right tool for the job. About 7" long from end to end, scrubby part is 1.5" x 0.5" with 0.5" bristles.
In stock
+
Add to wish list

US$5.17
This little dongle will let you connect one of our 5V 2Amp or 5V 10Amp adapters to something that expects to connect to USB. The premise is simple - one end has a USB A female jack and the other has a 'standard' 5.5mm OD/2.1mm ID barrel jack with center positive polarity. 
In stock
+
Add to wish list

US$5.17
This adapter will let you plug into a US 2-prong power adapter in the following locations: Bahrain, Bangladesh, Belize, Bhutan, Channel Islands, China, Cyprus, Dominica, Falkland Islands, Gambia, Ghana, Gibraltar, Grenada, Guatemala, Guyana, Hong Kong, Indonesia, Iraq, Ireland, Isle of Man, Jordan, Kenya, Kuwait, Lebanon, Macau, Malawi, Malaysia, Maldives, Malta, Mauritius, Myanmar, Nigeria, Oman, Qatar, St. Kitts and Nevis, St. Lucia, St. Vincent, Saudi Arabia, Seychelles, Sierra Leone, Singapore, Tanzania, Uganda, United Arab Emirates, United Kingdom, Vietnam, Yemen, Zambia, Zimbabwe.
Delivery within 2-3 weeks
+
Add to wish list

US$5.17
This microswitch has a 3" long wire lever actuator and three terminals. Sometimes called 'coin switches' - they're used in coin detectors. The terminals are along the bottom (the other microswitches have them on the sides).
In stock
+
Add to wish list

US$5.17
This keypad has 4 buttons, and since every key has its own wire line, no matrix code is required - just treat these like every day switches. The membrane is soft and has a removable paper backing to expose a strong adhesive so you can stick this on an enclosure and feed the cable through a slot.
In stock
+
Add to wish list

US$5.17
This 3" diameter speaker cone is the perfect addition to any audio project where you need an 8 ohm impedance and 1W or less of power. We particularly like this cone as it has 4 handy mounting tabs 60mm apart.
In stock
+
Add to wish list

US$5.17
Double up your power adapters with this wonderfully simple 2-way power jack splitter. All you have to do is connect a standard 5.5mm/2.1mm sized plug into one end, and behold, two identical plugs to use!
In stock
+
Add to wish list

US$5.17
Go 'cold splice' with these snap-able plastic splices for fast connections. Use with any 19-26 AWG solid core wire and slip them into the plastic splice so that they slide into the metal teeth. Then squeeze down with parallel-jaw or slip joint pliers - don't use needle-noses, they have too much angle and not enough force.
In stock
+
Add to wish list

US$5.17
Go 'cold splice' with these snap-able plastic splices for fast connections. Use with any 22-26 AWG solid core wire and slip them into the plastic splice so that they slide into the metal teeth. Then squeeze down with parallel-jaw or slip joint pliers - don't use needle-noses, they have too much angle and not enough force.
In stock
+
Add to wish list

US$5.17
Go 'cold splice' with these snap-able plastic splices for fast connections. Use with any 22-26 AWG solid core wire and slip them into the plastic splice so that they slide into the metal teeth. Then squeeze down with parallel-jaw or slip joint pliers - don't use needle-noses, they have too much angle and not enough force.
In stock
+
Add to wish list

US$5.17
Each LED is encased in a 3.5mm thick strip of a acrylic.
In stock
+
Add to wish list

US$5.17
This cable will let you swap out the stock 150mm long flex cable from a Raspberry Pi Camera (either 'classic' or 'NoIR' type) for a different size.
In stock
+
Add to wish list